Abstract:A composite ion‐conducting protective layer of MoS2/solid polymer is designed onto Li1.3Al0.3Ti1.7(PO4)3 (LATP), improving its poor Li/LATP interfacial contact and slow Li‐ion migration issues, which obtains excellent electrochemical performance. This study emphasizes the importance of promoting ion migration and adsorption in improving the interface, confirmed by density functional theory calculations and a series of experimental characterizations. Li1.3Al0.3Ti1.7(PO4)3 (LATP) is one of the most attractive solid‐state electrolytes (SSEs) for application in all‐solid‐state lithium batteries (ASSLBs) due to its advantages of high ionic conductivity, air stability and low cost. However, the poor interfacial contact and slow Li‐ion migration have greatly limited its practical application. Herein, a composite ion‐conducting layer is designed at the Li/LATP interface, which a MoS2 film is constructed on LATP via chemical vapor deposition, followed by the introduction of a solid polymer (SP) liquid precursor to form a MoS2@SP protective layer. This protective layer not only achieves a lower Li‐ion migration energy barrier, but also adsorbs more Li‐ion, which is able to promote interfacial ion transport and improve interfacial contacts. Thanks to the improved migration and adsorption of Li‐ion, the Li symmetric cell containing LATP‐MoS2@SP exhibits a stable cycle of more than 1200 h at 0.1 mA cm−2. More remarkably, the capacity retention of the full cell assembled with LiFePO4 cathode is as high as 86.2% after 400 cycles at 1 C. This work provides a design strategy for significantly improving unstable interfaces of SSEs and realizing high‐performance ASSLBs.

Stabilizing LATP Electrolyte Interface of All-Solid-State Lithium Ion Batteries Consisting of High-Voltage Cathode

Interface engineering of Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub> ceramic electrolyte via multifunctional interfacial layer for all-solid-state lithium batteries

Stabilizing Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub>|Li Metal Anode Interface in Solid-State Batteries by Kevlar Aramid Nanofiber-Based Protective Coating

Stabilization the Interface of NASICON-type Solid Electrolyte and Li metal by Al Interlayer

Recent Advances in Li1+xAlxTi2−x(PO4)3 Solid-State Electrolyte for Safe Lithium Batteries

Stabilizing Li1.3Al0.3Ti1.7(PO4)3|Li Metal Anode Interface in Solid‐State Batteries by Kevlar Aramid Nanofiber‐Based Protective Coating

Enhancing the cycling stability of all-solid-state lithium-ion batteries assembled with Li1.3Al0.3Ti1.7(PO4)3 solid electrolytes prepared from precursor solutions with appropriate pH values

Designing the Interface Layer of Solid Electrolytes for All‐Solid‐State Lithium Batteries

Ultrathin single-ion conducting polymer enabling a stable Li|Li1.3Al0.3Ti1.7(PO4)3 interface

Tailoring of Li/LATP-PEO Interface via a Functional Organic Layer for High-Performance Solid Lithium Metal Batteries

LATP-coated LiNi0.8Co0.1Mn0.1O2 cathode with compatible interface with ultrathin PVDF-reinforced PEO-LLZTO electrolyte for stable solid-state lithium batteries

Construction of Polyvinylidene Fluoride Buffer Layers for Li1.3Al0.3Ti1.7(PO4)(3) Solid-State Electrolytes toward Stable Dendrite-Free Lithium Metal Batteries

Engineering and regulating the interfacial stability between Li1.3Al0.3Ti1.7(PO4)3-based solid electrolytes and lithium metal anodes for solid-state lithium batteries

Stabilizing the Interface of NASICON Solid Electrolyte Against Li Metal with Atomic Layer Deposition.

In Situ Gelation of a 1,3-Dioxolane Dual-Permeable Porous Tandem Framework with Excellent Interfacial Stability to Power Long-Cycling Solid-State Lithium Metal Batteries

Understanding the Positive Effect of LATP in Polymer Electrolytes in All-Solid-State Lithium Batteries

Roles of Lithium Aluminum Titanium Phosphate in Lithium Batteries

LATP-coated LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode with Compatible Interface with Ultrathin PVDF-reinforced PEO-LLZTO Electrolyte for Stable Solidstate Lithium Batteries

Progress and Perspective of Li 1 + X Al X Ti 2 ‐x ( PO 4 ) 3 Ceramic Electrolyte in Lithium Batteries

Asymmetric Solid-State Lithium-Metal-Battery Electrolytes Featuring Na Superionic Conductor-Type Ceramic and Garnet-Type Ceramic Filled Composite Polymer

Stable Interface Between Lithium and Electrolyte Facilitated by a Nanocomposite Protective Layer