Abstract:Abstract Polyethylene oxide (PEO)‐based polymer solid electrolytes (PSE) have been pursued for the next‐generation extremely safe and high‐energy‐density lithium metal batteries due to their exceptional flexibility, manufacturability, and lightweight nature. However, the practical application of PEO‐PSE has been hindered by low ionic conductivity, limited lithium‐ion transfer number ( t Li+ ), and inferior stability with lithium metal. Herein, an ultrathin composite solid‐state electrolyte (CSSE) film with a thickness of 20 μm, incorporating uniformly dispersed two‐dimensional fluorinated boron nitride (F‐BN) nanosheet fillers (F‐BN CSSE) is fabricated via a solution‐casting process. The integration of F‐BN effectively reduces the crystallinity of the PEO polymer matrix, creating additional channels that facilitate lithium‐ion transport. Moreover, the presence of F‐BN promotes an inorganic phase‐dominated electrolyte interface film dominated by LiF, Li 2 O, and Li 3 N on the lithium anode surface, greatly enhancing the stability of the electrode‐electrolyte interface. Consequently, the F‐BN CSSE exhibits a high ionic conductivity of 0.11 mS cm −1 at 30°C, high t Li+ of 0.56, and large electrochemical window of 4.78 V, and demonstrates stable lithium plating/striping behavior with a voltage of 20 mV for 640 h, effectively mitigating the formation of lithium dendrites. When coupled with LiFePO 4 , the as‐assembled LiFePO 4 |F‐BN CSSE|Li solid‐state battery achieves a high capacity of 142 mAh g −1 with an impressive retention rate of 82.4% after 500 cycles at 5 C. Furthermore, even at an ultrahigh rate of 50 C, a capacity of 37 mAh g −1 is achieved. This study provides a novel and reliable strategy for the design of advanced solid‐state electrolytes for high‐rate and long‐life lithium metal batteries.

Stabilizing Solid Electrolyte-Anode Interface in Li-Metal Batteries by Boron Nitride-Based Nanocomposite Coating

Fluorinated boron nitride nanosheet enhanced ultrathin and conductive polymer electrolyte for high‐rate solid‐state lithium metal batteries

Synergistic Dual-Additive Regulated Carbonate Electrolyte Stabilizes Bidirectional Interface for Aggressive Ni-rich Li-metal Full Batteries

Stable Interface Between Lithium and Electrolyte Facilitated by a Nanocomposite Protective Layer

Highly Stable Quasi‐Solid‐State Lithium Metal Batteries: Reinforced Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 /Li Interface by a Protection Interlayer

Highly Conductive and Stable Composite Polymer Electrolyte with Boron Nitride Nanotubes for All-Solid-State Lithium Metal Batteries

Stabilized Solid Electrolyte Interphase Induced by Ultrathin Boron Nitride Membranes for Safe Lithium Metal Batteries

Improvement of the Interface between the Lithium Anode and a Garnet-Type Solid Electrolyte of Lithium Batteries Using an Aluminum-Nitride Layer

High-performance lithium metal batteries based on composite solid-state electrolytes with high ceramic content

Stabilizing Li1.3Al0.3Ti1.7(PO4)3|Li Metal Anode Interface in Solid‐State Batteries by Kevlar Aramid Nanofiber‐Based Protective Coating

Boron Nitride‐Based Release Agent Coating Stabilizes Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 /Li Interface with Superior Lean‐Lithium Electrochemical Performance and Thermal Stability

Stabilizing Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub>|Li Metal Anode Interface in Solid-State Batteries by Kevlar Aramid Nanofiber-Based Protective Coating

Boron Nitride‐Based Release Agent Coating Stabilizes Li1.3Al0.3Ti1.7(PO4)3/Li Interface with Superior Lean‐Lithium Electrochemical Performance and Thermal Stability

LATP-coated LiNi0.8Co0.1Mn0.1O2 cathode with compatible interface with ultrathin PVDF-reinforced PEO-LLZTO electrolyte for stable solid-state lithium batteries

Stabilization the Interface of NASICON-type Solid Electrolyte and Li metal by Al Interlayer

Stable All-Solid-state Lithium Metal Batteries with Li3N-LiF-enriched Interface Induced by Lithium Nitrate Addition

Stabilized Cathode/Sulfide Electrolyte Interface through Conformally Interfacial Nanocoating for All-Solid-State Batteries

LATP-coated LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode with Compatible Interface with Ultrathin PVDF-reinforced PEO-LLZTO Electrolyte for Stable Solidstate Lithium Batteries

A novel nanocomposite electrolyte with ultrastable interface boosts long life solid-state lithium metal batteries

Stabilizing the Interface of NASICON Solid Electrolyte Against Li Metal with Atomic Layer Deposition.

In Situ Construction of Li3N-enriched Interface Enabling Ultra-Stable Solid-State LiNi0.8Co0.1Mn0.1O2/lithium Metal Batteries