Abstract:Dissimilar metal weld (DMW) is a common structure in nuclear power plants to connect the materials with different properties, but is always encountered with the reliability problems due to the complexities in the structures and compositions. The case addressed in this paper involves the disbonding failure and the welding process optimization for the water chamber divider plate that connects the channel head and the tubesheet of the steam generator. During overlaying of the breaches on the corner of the divider plate, disbonding was discovered by ultrasonic testing occurring on the interface between the E309L and E308L stainless-steel cladding and the 18MND5 low-alloy steel base material of the channel head. To deal with this frequent problem, systematical experimental analyses were performed, including optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS) and microhardness testing, the microstructures evolution as well as the distribution of chemical compositions and hardness across the weld were investigated. Especially, the Type II boundaries were found adjacent to and parallel to the fusion line, and were eventually determined as the root cause of this disbonding failure by acting as the cracking initiation and propagation paths under the combined effects among the residual stresses from the structural mismatch, the thermal stresses from the CTEs mismatch and the tensile stresses from overlaying of the breach. The formation mechanism of the transition zone around the Type II boundaries was also discussed, which consisted of the stainless-steel cladding, the carburized layer with martensite, the fusion line and the decarburized layer. The corresponding optimization countermeasures were finally proposed point by point, and were proved effective indeed by the manufacturers of the steam generator.

Performance and damage behaviors of detonation sprayed W/Fe/steel coatings under transient high heat fluxes

Tungsten Joining with Copper Alloy and Its High Heat Load Performance

Characterization of Ductile Nano-Tic Dispersed V4Cr4Ti/RAFMs Solid Diffusion Joint for Nuclear Fusion Reactor Application

Progress of High Heat Flux Component Manufacture and Heat Load Experiments in China

Study on the Microstructure and Properties Evolution of CuCrZr/316LN-IG Explosion Bonding for ITER First Wall Components

Blistering Behavior and Deuterium Retention in Tungsten Vanadium Alloys Exposed to Deuterium Plasma in the Linear Plasma Device STEP

Surface Cracking of Tungsten-Vanadium Alloys under Transient Heat Loads

Mechanical properties of the W coating and interface of vacuum-plasma-sprayed W–ferritic steel joints under shear and bending loads

Microstructure of Tungsten Coatings Effect on Deuterium Plasma-Driven Permeation Through RAFM Steel

Investigation on W/Fe Diffusion Bonding Using Ti Foil and Ti Powder Interlayer by Sps

Welding Process Optimization for Steam Generator Divider Plate Against Disbonding of Dissimilar Metal Weld

Transient thermal shock and helium ion irradiation damage behaviors of ODS-W/CuCrZr joints

Stable bonding of W and ODS steel fabricated by TLP diffusion technology through inserting a novel composite interlayer Zr/Cu

Recent progress of thick tungsten coating prepared by chemical vapor deposition as the plasma-facing material

On the use of CoCrFeNi high entropy alloy as a new interlayer for achieving high strength diffusion bonded tungsten/steel joint

Interfacial characterization of dissimilar-metals bonding between vanadium alloy and Hastelloy X alloy by explosive welding

Interfacial microstructure and strengthening mechanism of W/steel diffusion bonding joint using a porous NiFeWss interlayer prepared by in-situ reduction

Damage Behavior of REE-doped W-based Material Exposed to High-Flux Transient Heat Loads

Experimental study on corrosion compatibility of laser-welded ODS steel with liquid lead lithium

Effect of bonding process on the microstructures and strength of W/steel joints with a W-Cu-Ni interlayer

Recent progress on preparation routes and performance evaluation of ODS/CDS-W alloys for plasma facing materials in fusion devices