Abstract:The hard-to-process properties associated with high hardness and high brittleness of sapphire drastically limit the services of optics, low-damage or damage-free properties are essential to the performance of sapphire optics. To achieve efficient and damage-free sapphire optics, a series of experiments involving ultra-precision grinding, polishing, and ion beam polishing were conducted. Initially, the surface and subsurface characteristics of sapphire ultra-precision grinding were examined, and the evolution of damage during polishing was discussed. Chemical etching was performed to evaluate the subsurface damage caused by polishing, ion beam polishing was used to eliminate subsurface damage. Finally, focused ion beam (FIB) and transmission electron microscopy (TEM) were employed to analyze the atomic structure of the subsurface. The results demonstrated that ultra-precision grinding can produce a ductile grinding surface and minimize subsurface damage, the difference in grinding damage on the outside and center of the workpiece was suppressed. The evolution of the surface roughness and damage behavior during polishing varied depending on the specific grinding strategy, ultra-precision grinding decreased damage removal time by 1/4. Photothermal absorption was utilized to monitor the damage progression during the polishing process and detect the presence of subsurface damage beneath the Beilby layer. Etching revealed that the subsurface damage was primarily caused by scratches, which was effectively eliminated after ion beam polishing. High-magnification TEM images provided compelling evidence of damage at the close-to-atomic scale for sapphire optics. Only amorphous structures smaller than 2 nm were observed on the subsurface, most of the atomic structure remained intact, albeit with irregular arrangement. Additionally, the grinding marks were mitigated after polishing.

Study on the grinding characteristics of sapphire with the assistant of cerium oxide liquid

Studies on the Surface Quality of the Unsteady-State Grinding Technique

An Experimental Investigation of Sapphire Grinding by Porous and Vitrified M0.5/1.5 Diamond Grinding Wheel

Longitudinal-torsional compound ultrasonic vibration end grinding sapphire: A study on surface topography and roughness

Experimental Study on Near-Polished Ultra-Precision Grinding of Fused Glass with the Assistant of Pure CeO2 Atomizing Liquid

Preparation of Non-Spherical Silica Composite Abrasives by Lanthanum Ion-Induced Effect and Its Chemical–mechanical Polishing Properties on Sapphire Substrates

Piezoelectric Ultrasonic Local Resonant Ultra-Precision Grinding for Hard–Brittle Materials

Evaluation of Grinding Characteristics for Sapphire Ultra-Precision Grinding Using Small Grit Sizes Wheels Based on AE Signals

2205 Grinding Performance of Spiral Ultrasonic Assisted Grinding for Monocrystal Sapphire Using Vitrified Diamond Wheel

Surface and subsurface microscopic characteristics in sapphire ultra-precision grinding

Grinding Force Characteristics in Elliptical Ultrasonic Assisted Grinding (EUAG) of Monocrystal Sapphire

A Feasibility Study on Elliptical Ultrasonic Assisted Grinding of Sapphire Substrate

Influence of SiO 2 –ZnO mixed soft abrasive on tribological behavior and polishing performance of sapphire wafer

Effect of different grinding strategies on subsequent polishing processes of sapphire

An Investigation on Wear Mechanism of Resin-Bonded Diamond Wheel in Elliptical Ultrasonic Assisted Grinding (EUAG) of Monocrystal Sapphire

E22 Fundamental Grinding Characteristics of Sapphire Wafer in Spiral Ultrasonic Vibration Assisted Grinding

Experimental Investigations of Grinding Forces in Elliptical Ultrasonic Assisted Grinding (euag) of Monocrystal Sapphire

Fe-Nx/C Assisted Chemical–mechanical Polishing for Improving the Removal Rate of Sapphire

Study on Chemical Mechanical Polishing Performances of Sapphire Wafer (0001) Using Silica-Based Slurry

A Two-Dimensional Ultrasonically Assisted Grinding Technique for High Efficiency Machining of Sapphire Substrate

Analysis on ground surface in ultrasonic face grinding of silicon carbide (SiC) ceramic with minor vibration amplitude