Abstract:Bulk Acoustic Wave (BAW) filters find applications in radio frequency (RF) communication systems for Wi-Fi, 3G, 4G, and 5G networks. In the beyond-5G (potential 6G) era, high frequency bands (>8 GHz) are expected to require resonators with high-quality factor (Q) and electromechanical coupling (k_t^2) to form filters with low insertion loss and high selectivity. However, both the Q and k_t^2 of resonator devices formed in traditional uniform polarization piezoelectric films of aluminum nitride (AlN) and aluminum scandium nitride (AlScN) decrease when scaled beyond 8 GHz. In this work, we utilized 4-layer AlScN periodically poled piezoelectric films (P3F) to construct high frequency (~17-18 GHz) resonators and filters. The resonator performance is studied over a range of device geometries, with the best resonator achieving a k_t^2 of 11.8% and a Q_p of 236.6 at the parallel resonance frequency (fp) of 17.9 GHz. These resulting figures of merit are ((FoM)_1=(k_t^2 Q)_p and (FoM_2=f_p(FoM)_1x10^-9) ) 27.9 and 500 respectively. These and the k_t^2 are significantly higher than previously reported An/AlScN-based resonators operating at similar frequencies. Fabricated 3-element and 6-element filters formed from these resonators demonstrated low insertion losses (IL) of 1.86 dB and 3.25 dB, and -3 dB bandwidths (BW) of 680 MHz (fractional BW of 3.9%) and 590 MHz (fractional BW of 3.3%) at ~17.4 GHz center frequency. The 3-element and 6-element filters achieved excellent linearity with in-band input third-order intercept point (IIP3) values of +36 dBm and +40 dBm, respectively, which are significantly higher than previously reported acoustic filters operating at similar frequencies.

18 GHz Solidly Mounted Resonator in Scandium Aluminum Nitride on SiO2/Ta2O5 Bragg Reflector

ScAlN-on-SiC Ku-Band Solidly-Mounted Bidimensional Mode Resonators

High speed surface acoustic wave and laterally excited bulk wave resonator based on single-crystal non-polar AlN film

Scandium Aluminum Nitride Overmoded Bulk Acoustic Resonators for Future Wireless Communication

Millimeter Wave Thin-Film Bulk Acoustic Resonator in Sputtered Scandium Aluminum Nitride Using Platinum Electrodes

C-Band Lithium Niobate on Silicon Carbide SAW Resonator With Figure-of-Merit of 124 at 6.5 GHz

Near 6 GHz Sezawa Mode Surface Acoustic Wave Resonators using AlScN on SiC

A 5.3 GHz Al0.76Sc0.24N Two-Dimensional Resonant Rods Resonator with a kt2 of 23.9%

A Scandium Doped Aluminum Nitride Thin Film Bulk Acoustic Resonator

A High Quality Factor, 19-GHz Periodically Poled AlScN BAW Resonator Fabricated in a Commercial XBAW Process

Solidly Mounted Resonators with Ultra‐High Operating Frequencies Based on 3R‐MoS2 Atomic Flakes

Full-epitaxial ScAlN and MgZnO solidly mounted resonators based on epitaxial acoustic Bragg reflector

Periodically Poled Aluminum Scandium Nitride Bulk Acoustic Wave Resonators and Filters for Communications in the 6G Era

Monocrystalline AlGaAs heterostructures for high-reflectivity high-Q micromechanical resonators in the MHz regime

Aluminum scandium nitride thin-film bulk acoustic resonators for 5G wideband applications

Thin-Film Lithium Niobate Acoustic Resonator with High Q of 237 and k2 of 5.1% at 50.74 GHz

Single Crystal Bulk Acoustic Resonator for 5 GHz and High-Power Applications

Three-Dimensional Finite Element Analysis and Characterization of Quasi-Surface Acoustic Wave Resonators

Plasma-enhanced chemical vapor deposition a-SiOCN:H low-Z thin films for bulk acoustic wave resonators

Rayleigh Wave Suppression in Al0.6Sc0.4N-on-SiC Resonators

Complementary-Switchable Dual-Mode SHF Scandium-Aluminum Nitride BAW Resonator