Abstract:The DSC analysis and heat treatment of the newly proposed Al0.2CrNbTiV lightweight refractory high-entropy alloy prepared by vacuum arc melting was investigated, and the evolutions of the microstructure and mechanical properties of the alloy after homogenization annealing at 650 degrees C, 850 degrees C and 1050 degrees C for 12 h were analyzed. The results show that the Al0.2CrNbTiV high-entropy alloy could maintain stable BCC solid solution structure from room temperature to 800 degrees C. The alloy annealed at 650 degrees C exhibited simple BCC structure with coarse equiaxed grains; after annealing at 850 degrees C, fine acicular and irregular block-like C14 Laves phases were uniformly precipitated in the grain and grain boundaries, meanwhile, the C14 Laves phase get coarser with the annealing temperature increased to 1050 degrees C. With the increase of annealing temperature, the microhardness of the Al0.2CrNbTiV alloy increased first and then decreased, reaching the maximum value of 692 HV after annealing at 850 degrees C. Due to the high dislocation density and the formation of kink bands, the alloy annealed at 650 degrees C showed a good combination of plastic and strength, with the work hardening ability strengthened simultaneously, the compressive yield strength could be up to 1454 MPa, with strain >50 %. Due to the precipitation of the hard and brittle C14 Laves phase, the load-bearing capacity of the alloy was reduced after annealing at 850 degrees C and 1050 degrees C. However, the wear resistance of the alloy also improved with the presence of the hard phase. The friction coefficient of Al0.2CrNbTiV alloy annealed at 650 degrees C is 0.67, with the abrasive wear acting as the main wear mechanism, and the alloy after annealing at 850 degrees C shew the best wear resistance, with the friction coefficient of 0.63, and delamination wear mechanism.

Nanoscale brittle-to-ductile transition of the C15 CaAl$_2$ Laves phase

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Strengthening of Mg-Al-Ca alloys with C15 and C36 Laves phases

Fracture of the $C$15 CaAl$_2$ Laves phase at small length-scales

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Influence of chemical composition on the room temperature plas-ticity of C15 Ca-Al-Mg Laves phases

Co-deformation Between the Metallic Matrix and Intermetallic Phases in a Creep-Resistant Mg-3.68Al-3.8Ca Alloy

ELEVATED TEMPERATURE MECHANICAL PROPERTIES AND BRITTLE-TO-DUCTILE TRANSITION OF A NiA1-Cr(Zr) ALLOY

Dynamic behavior and fracture mode of TiAl intermetallics with different microstructures at elevated temperatures

Elucidation of formation and transformation mechanisms of Ca-rich Laves phase in Mg-Al-Ca-Mn alloys

The Elevated Temperature Tensile Properties Of Nial-Cr(Zr) Multiphase Intermetallic Alloy

Strain heterogeneity and micro-damage nucleation under tensile stresses in an Mg-5Al-3Ca alloy with an intermetallic skeleton

Micro-compression of Al2Ca particles in a Mg-Al-Ca alloy

Atomistic Simulation of the Dislocation Interactions with the Al2Ca Laves Phase in Mg–Al–Ca Alloy

Brittle-To-Ductile Transition in Multiphase Nial Alloy

Microstructure, Brittle–ductile Transition Temperature and Elevated Temperature Compressive Behavior of the Directionally Solidified NiAl–Cr(Mo)–Hf Alloy

The Evolution of Microstructure and Mechanical Properties at Elevated Temperature of Cast Al–Li–Cu–Mg Alloys with Ni Addition

Atomistic simulation of the dislocation interactions with the Al 2 Ca Laves phase in Mg–Al–Ca alloy

Strengthening Of An Al-Containing Austenitic Stainless Steel At High Temperature

Effect of Annealing Temperature on the Microstructure and Mechanical Properties of Al0.2CrNbTiV Lightweight Refractory High-Entropy Alloy

Unraveling hot deformation behavior and microstructure evolution of nanolamellar TiAl/Ti3Al composites