Abstract:Effects of different Cu concentrations on the microstructure, mechanical, and corrosion properties of the extruded Mg-2%Zn alloy were studied by the use of x-ray diffraction, optical microscopy, scanning electron microscopy, energy-dispersive spectroscopy, tensile testing, polarization, and electrochemical impedance spectroscopy (EIS) measurements. The hot-extruded Mg-2%Zn comprised an equiaxed grain structure with the average size of about 13 μm. By adding 5 wt.% Cu, the average grain size decreased to 4 μm, due to the grain refinement behavior of Cu addition. Microstructural observations confirmed the existence of the α-Mg matrix, Mg(Zn,Cu), and Mg(Zn,Cu)2 intermetallics. The results obtained from mechanical testing revealed that Cu addition along with applying hot extrusion increased the hardness significantly from 80 HBN, for Cu-free alloy, to 108 HBN for the extruded Mg-2%Zn-5%Cu alloy. By the addition of 0.5 wt.% Cu, the values of ultimate tensile strength (UTS), elongation, and ultimate compressive strength (UCS) changed from about 233 MPa, 16.8%, and 294 MPa to 260 MPa, 21.5%, and 335 MPa, respectively, as optimum levels. However, more Cu addition (i.e., 5 wt.%) decreased UTS, elongation, and UCS values to 242 MPa, 15.9%, and 272 MPa, respectively, by introducing a high volume fraction of the second phase. On the other hand, tensile yield strength and compressive yield strength increased gradually at higher Cu additions from 128 to 105 MPa in the case of the Cu-free extruded alloy to 165 and 156 MPa for the alloy containing 5 wt.% Cu, respectively. The polarization and EIS results indicated that the extrusion process eliminates the protective film from the Mg-2%Zn alloy surface. The Mg-2%Zn alloy exhibited the best anti-corrosion property among the studied alloys, as further Cu addition increased the intermetallic volume fractions and enhanced the corrosion rate, due to the galvanic couple effect.

Enhanced Degradability of Mg-2Gd Alloy by Alloying Cu

Enhanced degradation properties of Mg-Gd-Cu alloys by introducing profuse solute segregated stacking faults phase

Improving the corrosion resistance of MgZn1.2Gd Zr0.18 (x = 0, 0.8, 1.4, 2.0) alloys via Gd additions

Enhanced Mechanical Properties and Corrosion Resistance by Minor Gd Alloying with a Hot-Extruded Mg Alloy

Effect of minor Gd addition on microstructure, mechanical performance, and corrosion behavior of Mg–Y–Gd alloys

Improving tensile properties and corrosion resistance of Mg–Zn–Ca–Mn alloy via Gd addition

Roles of micro-alloyed Y and Gd in improving the corrosion resistance and mechanical properties of pure Mg

Influence of Cu Addition on the Microstructure, Mechanical, and Corrosion Properties of Extruded Mg-2%Zn Alloy

Improving the corrosion resistance of Mg-8Li-3Al-2Zn alloy by combining Gd alloying and hot extrusion

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Influences of Gd on the Microstructure and Strength of Mg–4.5Zn Alloy

Modified Microstructures and Corrosion Behaviors of Mg-Gd-Cu Alloys through Annealing Treatment

Corrosion resistance and degradation behavior of anodized Mg-Gd alloys: A comparative study

Effect of Alloying Mg on Corrosion Resistance of Cu at High Temperature

High-temperature oxidation behavior and corrosion behavior of high strength Mg-xGd alloys with high Gd content

Enhanced strength and corrosion resistant of Mg-Gd-Y-Al alloys by LPSO phases with different Al content

Microstructures and Mechanical Properties of the Mg–4.5Zn–xGd (x = 0, 2, 3 and 5) Alloys

Interfacial microstructure, mechanical properties and strengthening mechanism of Mg/Al bimetallic composites produced by a novel compound casting with the addition of Gd

Gd Added Mg Alloy for Biodegradable Implant Applications

A good balance between strength and ductility in Mg–Zn–Mn-Gd alloy

Comparative Study on Corrosion Behavior and Mechanism of As-Cast Mg–Zn–Y and Mg–Zn–Gd Alloys