Abstract:A series of hydrocracking catalysts based on mesoporous molecular sieves of MCM-41 and SBA-15 with different silica to alumina ratios was prepared. Nickel and molybdenum were used as active metals to impregnate the extrudates prepared by using molecular sieves. The catalysts were characterized for physical and chemical properties and evaluated for the hydrocraking of desulfurised vacuum gas oil. The conversion of DS-VGO was lower as compared to that of the catalyst based on USY zeolite. However, the gas yield was lower in case of mesoporous materials based catalysts. Introduction Zeolites are widely used as catalysts in petroleum refining and for the production of petrochemicals and fine chemicals. Recently, the breakthrough discovery of the M41S family mesoporous materials [1,2] exemplified by the MCM-41 bearing hexagonal-close-packed channels. Despite the excellent structural properties, the hydrothermal stability of MCM-41 and MCM-41-like mesoporous materials was reported as lower than their counter part zeolites. Recently, a new kind of mesoporous silica, SBA-15, has been synthesized with poly (alkylene oxide) triblock copolymers such as poly (ethylene oxide)-poly (propylene oxide)poly (ethylene oxide) (PEO-PPO-PEO) [3]. Beside its uniform and large pore size channels (4.6-30 nm), SBA-15 possesses thick walls (3.1-6.4 nm). Therefore, it has much higher hydrothermal stability than MCM-41 [3]. Owing to their extremely large surface area (generally exceeding 1000 mg) and ultra large pore size these mesoporous materials have attracted great practical and academic interest as acid-catalyzed reactions of large molecules such as hydroprocessing of residual oil [4-5]. In this study, the preparation of MCM-41 and SBA-15 with Si/Al 10, 20 and hydrocracking catalysts based on these mesoporous materials along with USY zeolite are presented. Commercial USY zeolite used in this study also has mesopores in it. Nickel and molybdenum are impregnated as active metals. Mesoporous materials and hydrocracking catalysts prepared were characterized by XRD, surface are, pore volume, pore-size distribution, particle size measurement, and acidity measurement by FTIR and ammonia TPD. The side crushing strength of the extrudates with alumina binder was also measured by crushing strength tester. The catalysts were evaluated for hydrocracking of desulfurized vacuum gas oil (DS-VGO). The hydrocracking activity was measured by GC-SIMDIST method and sulfur and nitrogen contents of the product were measured by elemental analyzer.

Hydrocracking catalyst containing small crystal grain Y-shaped molecular sieve and preparation method thereof

Carrier material containing molecular sieve and amorphous silica-alumina and preparation method thereof

Preparation of Fe@Si/S-34 Catalysts and Its Catalytic Performance for Syngas to Olefins

Preparation of Y-type molecular sieve based on bentonite and study of its performance in hydrocatalytic cracking of shale oil

One noble metal hydrogenation catalyst and its preparation method and application

Synthesis of Nanoporous Flower-like Y-SAPO-11 Composite Molecular Sieves for Hydrocracking of n -Hexadecane

Bifunctional catalyst with high efficiency for converting hydrocarbons: The enhanced diffusion between micro and meso-pores

Synthesis and Catalytic Evaluation of Mesoporous Molecular Sieve Supported Hydrocracking Catalysts

Hydrocracking of Heavy Oil Using Zeolites Y/Al-SBA-15 Composites As Catalyst Supports

Preparation method of honeycomb carrier catalyst for molecular sieve denitration

DEHYDROGENATION AND HYDRODESULFURIZATION ACTIVITY OF HETEROATOM-CONTAINING HMS MESOPOROUS MOLECULAR SIEVE CATALYSTS

Hydrocracking of Bio-Alkanes over Pt/Al-MCM-41 Mesoporous Molecular Sieves for Bio-Jet Fuel Production

Synthesis of Small Crystal Size Y Zeolite Catalysts with High Hydrocracking Performance on n -Hexadecane

Transformation of Syngas to Light Hydrocarbons over Bifunctional CuO–ZnO/SAPO-34 Catalysts: the Effect of Preparation Methods

Synergetic Regulation of the Microstructure and Acidity of HZSM-5/MCM-41 for Efficient Catalytic Cracking of n-Decane

A novel preparation strategy for an oil-soluble catalyst in slurry phase hydrocracking: Synergistic effect and electronic regulation of Fe on MoS 2

Effect of Zeolite-Y Modification on Crude-Oil Direct Hydrocracking

Synthesis and characterization of amorphous silica-alumina with enhanced acidity and its application in hydro-isomerization/cracking

A defect-based strategy for the preparation of mesoporous zeolite Y for high-performance catalytic cracking

Core-Shell Zeolite Y@Gamma-Al2o3 Nanorod Composites: Optimized Fluid Catalytic Cracking Catalyst Assembly for Processing Heavy Oil

Preparation of nano ZSM-5 with hydrophobic surfaces and application to catalytic cracking of hydrocarbon fuels