Abstract:This article is devoted to the experimental study of tuning method for an Alvarez-type drift tube linac (DTL) of the Compact Pulse Hadron Source (CPHS) project at Tsinghua University. The biperiodic structure based on the post couplers are introduced to overcome the instability of the Alvarez DTL tank which is used to operate in 0 (or 2π) mode. The experimental method and results are presented, and the tuning scheme for the formal CPHS DTL is summarized from the tuning experiment. INTRODUCTION The effective shunt impedance of the Alvarez-type DTL is typically high when it operates in a typical 0 (or 2π) mode with the group velocity of 0. But the structure is very susceptible to perturbation such as the beam loading, mechanical and installation error, because of the narrow space near the adjacent modes on the TM dispersion curve. The post couplers, which are the resonant-coupling elements constitutionally, are mounted on the wall of the DTL cavity oppositely and alternatively to introduce a new PCs (post couplers) dispersion curve. When the stopband between the two passbands of the dispersion curves disappears by adjusting the slugging length of the post couplers, the lowest frequency of the TM passband will be moved to the π/2 mode point of the new dispersion curve. Therefore the new stable biperiodic structure of the DTL will be achieved [1]. To verify the tuning method, one model cavity has been machined and the turning experiment is carried out based on the cavity. The cavity is designed and manufactured for verifying the mechanical design and undertaking some low-power experiment. The model cavity consists of ten full drift tubes, two half drift tubes mounted on the end flanges, three post couplers and two tuners [2]. The end of the post couplers is designed to be eccentric to facilitate the tuning of the local field distribution by rotating the post. TUNING EXPERIMENTAL CONFIGURATION On the experimental stand as shown in Fig. 1, the measurement based on the bead-pull method is executed. According to the perturbation theory, when the bead is pulled into the field between the two adjacent drift tubes, the resonant frequency changes. Then the corresponding phase shift can be detected by a vector network analyzer (VNA) and the electric field along the beam-axis can be deduced [3]. Figure: 1 Tuning experimental stand. A stepping motor is adopted to pull a fine nylon line on which the small perturbation bead is fixed. The size of the bead shall be rather appropriate, so that the responsive signal caused by the bead is big enough compared with the background noise and at the same time within the linear range of the phase around the resonant frequency. It depends on the Q factor of the cavity. The Q factor of this model cavity is measured as 17796 which is about 44% of the designed value. It is because that the surfaces of the interior copper-plated cavity wall and the aluminous end flanges are oxidic. With the value of the Q factor, the radius of the bead is determined as 0.7 mm by estimation. To ensure the accuracy of the measurement, the peak field is employed to represent the field distribution instead of the integral one due to its further advantages [4]. Before the measurement, the reproducibility is checked. The reproducibility Rij is defined by Eq. (1).

RF cavity design and qualification for proton accelerator

Conceptual Design of a Drift Tube Linac for Proton Therapy

Design, fabrication, and characterization of a drift tube linac type double gap re-buncher cavity

Design Study of Drift Tube Linac for BNCT Accelerator

RF design and study of a 325 MHz 7 MeV APF IH-DTL for an injector of a proton medical accelerator

Proposal and Design of an 81.25 MHz Interdigital H-mode Dual-Beam Drift Tube Linac

Radio frequency measurement and tuning of a 13 MeV Alvarez-type drift tube linac for a compact pulsed hadron source

Research on drift tube linac model cavity for CPHS

Development of a Compact 325 MHz Proton Interdigital H-mode Drift Tube Linac with High Shunt Impedance

RF AND PRIMARY BEAM DYNAMICS DESIGN OF A 325 MHz IH-DTL

Design and Realization of a Single Klystron-Based Radio Frequency System for a Radio Frequency Quadrupole and a Drift Tube Linac

Physics Design Of A Coupled Rfq-Dtl Cavity For A Compact Neutron Source

RF measurement and tuning for an Alvarez-type drift tube linear accelerator without post couplers

Proposal and design of 81.25 MHz heavy ion drift tube linacs for BISOL

The Study and Design of a Deuteron Drift Tube Linear Accelerator for Middle Energy Neutron Source

IH-DTL Design with Modified KONUS Beam Dynamics for a Synchrotron-Based Proton Therapy System

Experimental Study of Tuning Method on a Model Alvarez DTL Cavity for CPHS Project

Beam dynamic design of a high intensity injector for proton linac

The General RF Tuning for IH-DTL Linear Accelerators

Study and Design of the Coupled Cavity with Ladder RFQ and IH DTL Structure for Transportable Neutron Source