Abstract:Organic coatings are widely used to protect metals from corrosion in high-temperature marine environments. Compared with inorganic or metal coatings, organic coatings exhibit favorable properties, such as a reasonable cost, adequate flexibility, and easy fabrication. However, most organic coatings are limited to relatively short protection times and thus fail to meet the increasing demands for industrial applications. In this paper, graphene oxide (GO) was added to cyanate ester (CE) coatings as a corrosion inhibitive filler. Electrochemical analysis shows that a 3 wt % GO/CE coating has favorable corrosion protection properties with a low-frequency resistance higher than 106 Ω cm2 and a corrosion rate of 632.9 × 10–6 mm per year after 1320 h of immersion in a high-temperature marine environment. Top-view and cross-sectional SEM images identify the electrochemical results. Furthermore, chemical analyses by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy demonstrate that hydroxyl groups of GO can react with cyanate groups, and therefore, a robust cross-linked structure was formed in the GO/CE coating. The synergistic effect of the physical shielding of GO and the robust cross-linked structure makes the GO/CE coating a promising choice for corrosion protection of steel in high-temperature marine environments. Our study also illustrates a novel method for preparing other chemically cross-linked composite coatings.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsanm.0c02531?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsanm.0c02531</a>.Potentiodynamic polarization curves of different coatings; low-frequency impedance modulus at 0.01 Hz and breakpoint frequency of all coatings; photo digital images of different CE or GO/CE-coated specimens before and after immersion in 3.5 wt % NaCl solutions; surface morphology by SEM of different coatings; contact angle of pristine CE coating, 1.5 wt % GO/CE coating, and 3 wt % GO/CE coating; bode modulus and phase angle diagrams of 0.75 wt % GO/CE coatings on Q235 steel immersed in 3.5 wt % NaCl solution from 216 to 1320 h; bode modulus and phase angle diagrams of 3 and 5 wt % GO/CE coatings on Q235 steel immersed in 3.5 wt % NaCl solution for 48, 96, 144, and 216 h, respectively; low-frequency impedance modulus at 0.01 Hz of 3 and 5 wt % GO/CE coatings with different immersion times; adhesions of six different coatings before and after immersion in 3.5 wt % NaCl solutions for 216 h; heating temperature and corresponding heating time during the whole curing process; polarization parameters of different coatings; and O2 gas permeability of pristine CE and 3 wt % GO/CE composite membranes (<a class="ext-link" href="/doi/suppl/10.1021/acsanm.0c02531/suppl_file/an0c02531_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Preparation and performance study of waterborne epoxy resin/non-covalent modified graphene oxide hydrogen barrier coatings

Preparation and Properties of GO-SiO2 Anticorrosive Coatings

Preparation and Anticorrosive Performance of Waterborne Epoxy Resin Composite Coating with Amino-Modified Graphene Oxide

Experimental and simulation investigation on hydrophobicity and corrosion resistance of graphene oxide reinforced composite coating

Modified graphene oxide/waterborne epoxy composite coating with enhanced corrosion resistance

Computation of Binding Energy of MCS and GO-Grafted MCS with Waterborne Epoxy Resin Using Density Functional Theory Method: Investigating the Corrosion Resistance of the Composite Coatings.

Effect of cyanate ester and graphene oxide as modifiers on corrosion protection performance of epoxy composite coating in sulfuric acid solution

In-situ crosslinking reaction of graphene oxide & waterborne epoxy resin to construct continuous phase anticorrosive coating

Critical factors on corrosion protective waterborne coatings containing functionalized graphene oxide: A review

The synergistic effect of polyvinyl alcohol and graphene oxide on the corrosion resistance of waterborne coatings

Anti-corrosion reinforcement of waterborne polyurethane coating with polymerized graphene oxide by the one-pot method

“Labyrinthine structure” anticorrosive water-based composite coatings

Preparation and Performance Studies of Modified Graphene Oxide/polyaniline Composite Anticorrosive Coatings

Corrosion-Resistant Cross-Linked Cyanate Ester Coatings Doped by Graphene Oxide for Use in High-Temperature Marine Environments

Covalent modification of graphene oxide by metronidazole for reinforced anti-corrosion properties of epoxy coatings

Preparation of graphene oxide–boron nitride hybrid to reinforce the corrosion protection coating

Designing functionalized graphene-stitched-SiC/fluoropolymer novel composite coating with excellent corrosion resistance and hydrogen diffusion barrier properties

A long-term anti-corrosion and cathodic delamination resistant epoxy coating based on COF grafted GO nanofillers

Amino-Modified Graphene Oxide from Kish Graphite for Enhancing Corrosion Resistance of Waterborne Epoxy Coatings

A bi-layer orientated and functionalized graphene-based composite coating with unique hydrogen gas barrier and long-term anti-corrosion performance

Preparation and Corrosion Properties of Graphene Oxide Modified Waterborne Epoxy Zinc-Rich Coatings