Abstract:Organic coatings are widely used to protect metals from corrosion in high-temperature marine environments. Compared with inorganic or metal coatings, organic coatings exhibit favorable properties, such as a reasonable cost, adequate flexibility, and easy fabrication. However, most organic coatings are limited to relatively short protection times and thus fail to meet the increasing demands for industrial applications. In this paper, graphene oxide (GO) was added to cyanate ester (CE) coatings as a corrosion inhibitive filler. Electrochemical analysis shows that a 3 wt % GO/CE coating has favorable corrosion protection properties with a low-frequency resistance higher than 106 Ω cm2 and a corrosion rate of 632.9 × 10–6 mm per year after 1320 h of immersion in a high-temperature marine environment. Top-view and cross-sectional SEM images identify the electrochemical results. Furthermore, chemical analyses by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy demonstrate that hydroxyl groups of GO can react with cyanate groups, and therefore, a robust cross-linked structure was formed in the GO/CE coating. The synergistic effect of the physical shielding of GO and the robust cross-linked structure makes the GO/CE coating a promising choice for corrosion protection of steel in high-temperature marine environments. Our study also illustrates a novel method for preparing other chemically cross-linked composite coatings.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsanm.0c02531?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsanm.0c02531</a>.Potentiodynamic polarization curves of different coatings; low-frequency impedance modulus at 0.01 Hz and breakpoint frequency of all coatings; photo digital images of different CE or GO/CE-coated specimens before and after immersion in 3.5 wt % NaCl solutions; surface morphology by SEM of different coatings; contact angle of pristine CE coating, 1.5 wt % GO/CE coating, and 3 wt % GO/CE coating; bode modulus and phase angle diagrams of 0.75 wt % GO/CE coatings on Q235 steel immersed in 3.5 wt % NaCl solution from 216 to 1320 h; bode modulus and phase angle diagrams of 3 and 5 wt % GO/CE coatings on Q235 steel immersed in 3.5 wt % NaCl solution for 48, 96, 144, and 216 h, respectively; low-frequency impedance modulus at 0.01 Hz of 3 and 5 wt % GO/CE coatings with different immersion times; adhesions of six different coatings before and after immersion in 3.5 wt % NaCl solutions for 216 h; heating temperature and corresponding heating time during the whole curing process; polarization parameters of different coatings; and O2 gas permeability of pristine CE and 3 wt % GO/CE composite membranes (<a class="ext-link" href="/doi/suppl/10.1021/acsanm.0c02531/suppl_file/an0c02531_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Effect of cyanate ester and graphene oxide as modifiers on corrosion protection performance of epoxy composite coating in sulfuric acid solution

Corrosion-Resistant Cross-Linked Cyanate Ester Coatings Doped by Graphene Oxide for Use in High-Temperature Marine Environments

Modified graphene oxide/waterborne epoxy composite coating with enhanced corrosion resistance

Enhancing epoxy coating corrosion resistance with a novel MoS2-modified polydopamine functionalized graphene oxide nanocomposite

Preparation of modified montmorillonite/graphene oxide composites to enhance the anticorrosive performance of epoxy coatings

Preparation and anticorrosion properties of GO‐Ce‐MOF nanocomposite coatings

Graphene oxide–cerium oxide hybrids for enhancement of mechanical properties and corrosion resistance of epoxy coatings

Development of an epoxy resin-based anticorrosive coating enhanced by monolayer amino-modified graphene oxide

Incorporation of Graphene Oxide Modified with Polyamide Curing Agent into the Epoxy–Zinc Composite Coating for Promoting Its Corrosion Resistance

Engineering the interface in graphene oxide/epoxy composites using bio-based epoxy-graphene oxide nanomaterial to achieve superior anticorrosion performance

Experimental and simulation investigation on hydrophobicity and corrosion resistance of graphene oxide reinforced composite coating

“Labyrinthine structure” anticorrosive water-based composite coatings

Facile modification of graphene oxide with Lysine for improving anti-corrosion performances of water-borne epoxy coatings

Preparation and Anticorrosive Performance of Waterborne Epoxy Resin Composite Coating with Amino-Modified Graphene Oxide

Research on the Preparation and Anticorrosion Properties of EP/CeO2-GO Nanocomposite Coating

Amino-Modified Graphene Oxide from Kish Graphite for Enhancing Corrosion Resistance of Waterborne Epoxy Coatings

In-situ crosslinking reaction of graphene oxide & waterborne epoxy resin to construct continuous phase anticorrosive coating

Long-term corrosion protection of Q235 steel by graphene oxide composite coating

Preparation of polyvinylpyrrolidone/graphene oxide/epoxy resin composite coatings and the study on their anticorrosion performance

Effect of covalent organic framework modified graphene oxide on anticorrosion and self-healing properties of epoxy resin coatings

Phytic Acid Intercalated Graphene Oxide for Anticorrosive Reinforcement of Waterborne Epoxy Resin Coating