Abstract:Tracking microstructure transformation under industrial conditions is significant and urgent for the development of oxygen evolution reaction (OER) catalysts. Herein, employing iron foam (IF) as an object, we closely monitor related morphologies and composition evolution under 300 mA cm–2 at 40 °C (IF-40-t)/80 °C (IF-80-t) in 6 M KOH and find that the OER activity first increases and then decreases with the continuous generation of FeOOH. Moreover, the reasons for different tendencies of Tafel slope, double-layer capacitance, and impedance for IF-40-t/IF-80-t have been investigated thoroughly. In detail, the OER activity of IF-40-t is governed by electron and mass transport, while for IF-80-t, the dominating factor is electron transfer. Further, to improve the stability, guided by the above results, two versatile methods that do not sacrifice electron and mass transport have been proposed: surface coating and dynamic interface construction. The synchronous improvements of stability and activity are deeply revealed, which may provide inspiration for catalyst design for industrial applications.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.2c00016.Characterization; electrochemical measurements; XRD, SEM, and TEM images; XPS spectra; LSV curves; Tafel plots; Nyquist plots; Cdl curves; CV curves; table showing the Rct, Cdl, and ECSA values of IF and IF-40-t; table showing the comparison of jOER,specific,ratio between IF-80-t and IF-40-t; table showing the contents of Fe, P, C, and O elements in the catalyst detected using EDX spectroscopy; table showing the ratio of Ni2+/Ni3+; table showing the Rct, Cdl, and ECSA values of IF and IF-80-t; tables showing the contents of Fe, Ni, and O elements in Ni(OH)2@IF before and after OER stability; and tables showing Fe and Ni contents in KOH after long-term stability detected using ICP (PDF)This article has not yet been cited by other publications.

Tungsten Strongly Inhibits Sintering of Porous Iron During High‐Temperature Redox Cycling

Tungsten's Role in Enhancing Sintering Resistance of Fe‐W Hierarchical Foams during Redox Cycling

Pore morphology evolution and atom distribution of doped Fe2O3 foams developed by freeze-casting after redox cycling

Highly sintering-resistant iron oxide with a hetero-oxide shell for chemical looping water splitting

Achieving porous tungsten with high porosity by selective dissolution of W-Fe alloy

FeO controls the sintering of iron-based oxygen carriers in chemical looping CO2 conversion

Oxidation Behaviour of Feal Intermetallic Coatings Produced by Magnetron Sputter Deposition

Improvement of high-temperature oxidation resistance of WC–Co–Ni alloy by Cr3C2–CeO2–WS2 mixed additives and its mechanism

Enhanced Elevated-Temperature Tribological Properties and Microstructure of Co-continuous Iron Foam/SiC/Al-Si Dual-Reinforced Composites Fabricated by Vacuum-Assisted Infiltration

Oxidation behavior of high Cr white iron composites reinforced with TiC and nonstoichiometric TiC x in air at 600 °C

Achieving high strength and high ductility in WC-reinforced iron-based composites by laser additive manufacturing

Phase Transformations and Electrochemical Characterizations of Electrodeposited Amorphous Fe–W Coatings

Microstructure and Its High Temperature Oxidation Behavior of W-Cr Alloys Prepared by Spark Plasma Sintering

Phase, Microstructure and Properties Evolution of Fine-Grained W–Mo–Ni–Fe Alloy During Spark Plasma Sintering

High-Temperature Steam Oxidation and Surface Microstructure Evolution of Fe13Cr6Al(1–4)Mo0.15Y Alloys

Accelerated sintering of high-performance oxide dispersion strengthened alloy at low temperature

Active Microstructure Transformation and Enhanced Stability of Iron Foam Derived from Industrial Water Oxidation

The simultaneous improvement of strength and ductility of the 93W-4.6Ni-2.4Fe prepared by additive manufacturing via optimizing sintering post-treatment

High-temperature cyclic oxidation kinetics and microstructural transition mechanisms of Ti-6Al-4V composites reinforced with hybrid (TiC+TiB) networks

High-Temperature Cyclic Oxidation Behavior and Microstructure Evolution of W- and Ce-Containing 18Cr-Mo Type Ferritic Stainless Steel

Thermo‐mechanical performance of wolframite mineral reinforced siloxane‐modified epoxy‐based intumescent coating for structural steel