Abstract:Additive manufacturing (AM) introduces unique grain feature and anisotropy in metals, as well as relatively poor surface quality, so the knowledge about the formation of post-machining-induced surface integrity needs to be extended. This study aims to understand the machining phenomena in orthogonal cutting of Inconel 718 produced via powder bed fusion of metals using a laser beam system (PBF-LB/M), paying particular attention to the cutting energy, chip formation, geometrical defects, and microstructural deformation. Experiments are conducted on both wrought (W 718) and PBF-LB/M (PBF 718) Inconel 718, whereby the cutting speed and the anisotropy of the workpiece in the raw state play an important role. The results indicate that less cutting energy is consumed when cutting PBF 718 in the direction perpendicular to its build direction (BD), followed by cutting in its BD. Denser shearing-induced slip lines and relatively continuous chip morphology are found when cutting PBF 718 in its BD, moreover, the effect of cutting speed on shearing deformation of columnar grains under this condition is analysed. More importantly, this study identifies a significant geometrical defect phenomenon which is unique to PBF 718 and highly depends on the cutting speed and anisotropy of grain feature. A detailed characterisation shows that this behaviour is caused by tearing within the grains in the matrix material and not by the presence of hard inclusions, which has rarely been reported in the literature. The microstructure in the subsurface area exhibits that the density of grain boundaries in the cutting direction plays the key role in plastic deformation, as the machining process mainly causes dragging behaviour in the area below the machined surface. Thus, cutting PBF 718 in the direction perpendicular to its BD shows similar deformation layer to W 718, while cutting PBF 718 in its BD displays much stronger subsurface deformation. The obtained results greatly help to understand the cutting phenomena in post-machining of additively manufactured Ni-based components, especially the integrity for a better functional surface.

Determination of the anisotropy in mechanical properties of laser powder bed fusion Inconel 718 by ultrasonic testing

Microstructure and mechanical property comparison of Inconel alloys fabricated using micro and conventional laser powder bed fusion

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Mechanical Characterization of Near-Isotropic Inconel 718 Fabricated by Laser Powder-Bed Fusion

High-throughput investigation of laser powder bed fabricated Inconel 718 alloy: Fabrication, microstructure and performance

The Use of Miniature Specimens to Determine Local Properties and Fracture Behavior of LPBF-Processed Inconel 718 in as-Deposited and Post-Treated States

Influence of Deposition Parameters on Hardness Properties of InconelTM 718 Processed by Laser Powder Bed Fusion for Space Applications

Mechanical properties of laser powder bed fusion processed Inconel alloy IN718 in different heat treatment conditions through small scale specimen testing

Effect of post-processing on microstructure and mechanical properties of Alloy 718 fabricated using powder bed fusion additive manufacturing processes

Microstructures and High-Temperature Mechanical Properties of Inconel 718 Superalloy Fabricated via Laser Powder Bed Fusion

Laser Powder Bed Fusion of Inconel 718 on 316 Stainless Steel

Effect of heat treatment on the microstructure and mechanical properties of Inconel 718 processed by selective laser melting

Tensile and Low‐Cycle Fatigue Behavior of Laser Powder Bed Fused Inconel 718 at Room‐ and High Temperature

Microstructure and mechanical properties at elevated temperatures of as-built and heat-treated Inconel 718 produced through laser powder bed fusion processes

Impact of process parameters on the dynamic behavior of Inconel 718 fabricated via laser powder bed fusion

Effect of homogenization and solution treatments time on the elevated-temperature mechanical behavior of Inconel 718 fabricated by laser powder bed fusion

Unique crystallographic texture formation in Inconel 718 by laser powder bed fusion and its effect on mechanical anisotropy

Microstructural, mechanical and wear behaviour of Inconel-718 produced through laser-powder bed-fused additive manufacturing

On machining-induced surface integrity of Inconel 718 fabricated by powder bed fusion

Mechanical properties and microstructure evolution of selective laser melting Inconel 718 along building direction and sectional dimension

Mechanical Properties and Microstructure of Inconel 718 Lattice Structures Produced by Selective Laser Melting Process