Abstract:Inconel 718 has good fabricability, high strength at elevated temperatures, and high corrosion resistance and is widely deployed in many aerospace and other high-performance applications. With the molten pool's rapid solidification during laser powder bed fusion (LPBF), the resulting microstructures differ from those expected in equilibrium conditions. Residual stresses, microsegregation, anisotropy, undesirable phases, layered structure, and lower mechanical properties are the challenges that must be addressed before LPBF-ed Inconel 718 parts can be industrially implemented. Heat treatment of Inconel 718 after the LPBF process is widely discussed in the literature, and the proposed heat treatment processes do not address all the challenges mentioned above. For this reason, specific heat treatments should be designed to achieve desired mechanical properties. Four different high-temperature heat treatment procedures were developed and tested in recent work to study the effect of various heat treatment parameters on the type of precipitates, grain size, room and elevated temperature mechanical properties, and creep properties of LPBF-ed Inconel 718. Two heat treatment procedures were designed to study the effect of eliminating the stress relief cycle and increasing the soaking time of solution heat treatment at the same hot isostatic pressing (HIP) and aging conditions. The other two heat treatment procedures were designed to study the effect of stress relief and aging parameters, with similar HIP and solution annealing parameters. The investigated heat treatment procedures showed the formation of equiaxed grain size and a significant amount of γ ′′ particles at the grain boundary in addition to primary carbide types (MC). Three different grain sizes could be obtained, starting with the same as-built microstructure by controlling post-process heat treatment parameters. The first type, coarse grain size (ASTM grain size No. G 3), suitable for creep application, was achieved by increasing the soaking time at the aging cycle. The second type, the formation of serrated grain boundaries suitable for good fatigue and creep properties, was achieved by decreasing the stress relief cycle's soaking time and temperature. The third type, fine grain size (ASTM grain size No. G 6), which is preferable for fatigue properties, was achieved by decreasing the soaking time at the solution annealing cycle. Among the different heat treatment conditions, the heat treatment with lower stress relief temperature and longer soaking time at solution annealing steps showed compromised equiaxed grain size with serrated grain boundaries, and it was selected for mechanical testing. The mechanical properties at room and elevated temperature (650 °C) and creep properties under constant axial stress of 690 MPa at 650 °C until failure were evaluated. The obtained elongation is > 2 × higher than the available properties in the AMS 5663 for wrought Inconel 718, AMS 5383 for cast Inconel 718, and ASTM F3055 for LPBF while maintaining a higher tensile strength above the average level found in the standards. It can be concluded that the performed heat treatment achieves higher mechanical properties. The values of UTS, YS, elongation, and reduction of area percentages are similar in the Z and XY orientations, revealing the presence of isotropic microstructure and uniform distribution of MC and γ ′′ precipitates.

Studies on the metabolism of adipose tissue. II. The effect of changes in the ionic composition of the medium upon the response to insulin.

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Mechanical Characterization of Near-Isotropic Inconel 718 Fabricated by Laser Powder-Bed Fusion

Experimental investigation of process parameter variations on the microstructure and failure behavior of IN718 structures in PBF-LB/M

Determination of the anisotropy in mechanical properties of laser powder bed fusion Inconel 718 by ultrasonic testing

Microstructure and mechanical properties at elevated temperatures of as-built and heat-treated Inconel 718 produced through laser powder bed fusion processes

Microstructure and mechanical property comparison of Inconel alloys fabricated using micro and conventional laser powder bed fusion

Mechanical properties of laser powder bed fusion processed Inconel alloy IN718 in different heat treatment conditions through small scale specimen testing

Microstructural, mechanical and wear behaviour of Inconel-718 produced through laser-powder bed-fused additive manufacturing

Effect of heat treatment on the microstructure and mechanical properties of Inconel 718 processed by selective laser melting

A study of the influence of novel scan strategies on residual stress and microstructure of L-shaped LPBF IN718 samples

In Envelope Additive/Subtractive Manufacturing and Thermal Post-Processing of Inconel 718

Unique crystallographic texture formation in Inconel 718 by laser powder bed fusion and its effect on mechanical anisotropy

Tensile and Low‐Cycle Fatigue Behavior of Laser Powder Bed Fused Inconel 718 at Room‐ and High Temperature

Knowledge of process-structure-property relationships to engineer better heat treatments for laser powder bed fusion additive manufactured Inconel 718

Impact of annealing treatment on the fatigue behavior of Inconel 625 produced by laser‐based powder bed fusion

Impact of process parameters on the dynamic behavior of Inconel 718 fabricated via laser powder bed fusion

Effect of Scanning Strategies on the Microstructure and Mechanical Properties of Inconel 718 Alloy Fabricated by Laser Powder Bed Fusion

Tailored microstructure by using in-situ re-scanning and its influence on fatigue crack growth behavior of Inconel 718 fabricated by LPBF at elevated temperature

Mechanical properties and microstructure evolution of selective laser melting Inconel 718 along building direction and sectional dimension

Optimization of the Post-Heat Treatment of Additively Manufactured IN718