Abstract:The foamed structure of the central layer, predominantly governed by the addition levels of TiH 2 and the composition of the precursor, in addition to the parameters associated with the foaming process, constitutes the pivotal determinant impacting the spectrum of applications for aluminum foam sandwiches. Systematic research on the foaming behavior of the AlMg 4 Si 8 matrix and pure Al matrix precursors in closed cavities with different TiH 2 addition levels was conducted. The results reveal that with the increasing amount of TiH 2 , specifically at a 200% expansion rate of AlMg 4 Si 8 foams, the number of large pores decreased, the average pore size decreased from 0.67 mm 2 (0.6 wt%) to 0.43 mm 2 (1.0 wt%), and the total number of pores increased from 125 (0.6 wt%) to 156 (1.0 wt%). This trend of pore size consistency was evident not only at the mentioned 200% expansion rate but also across different expansion rates of AlMg 4 Si 8 foams and across all expansion rates of pure Al foams. The pore structures observed in the AlMg 4 Si 8 matrix and pure aluminum matrix foams within a closed cavity exhibited significantly superior characteristics compared to those achieved through free foaming processes. The circularity of pure Al foams was mainly distributed in the range of 1–2, being higher than the AlMg 4 Si 8 foams (1–1.5) due to their low viscosity and foam stability. The compressive curve of AlMg 4 Si 8 foams at a 400% expansion rate reveals that as the average cross-sectional area increased, there was a higher likelihood of experiencing initial collapse conditions. Additionally, the fluctuation of the platform area became more pronounced. Further, the slope corresponding to the elastic stage of the compressive curve increased as the overall stress levels increased.

Microstructure and mechanical properties of bimodal syntactic foams with different size combination and volume fraction of alumina hollow spheres

Factors affecting the microstructure of a fine ceramic foam

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Preparation and Compressive Performance of an A356 Matrix Syntactic Foam

Interface characterization and mechanical property of an aluminum matrix syntactic foam with multi-shelled hollow sphere structure

Mechanical Behavior of Pure Al and Al–Mg Syntactic Foam Composites Containing Glass Cenospheres

Microstructure and compression behavior of cenosphere filled aluminum syntactic foams

Microstructure and Strength Correlation of Pure Al and Al-Mg Syntactic Foam Composites Subject to Uniaxial Compression

Compressive properties of expanded glass and alumina hollow spheres hybrid reinforced aluminum matrix syntactic foams

Microstructure and Compressive Properties of Aluminum Foams Made by 6063 Aluminum Alloy and Pure Aluminum

Quasi-static and High Strain Rates Compressive Behavior of Aluminum Matrix Syntactic Foams

Controllable Design of Structural and Mechanical Behaviors of Al‐Si Foams by Powder Metallurgy Foaming

Foamability and mechanical properties of in situ submicron MgAl2O4p/Al composite foams by ultrasonic method

Characterization of as-cast microstructure of aluminum foams by melt foaming method

Mg-matrix syntactic foam filled with alumina hollow spheres coated by MgO synthesized with solution coating-sintering

Effects of particle size, bimodality and heat treatment on mechanical properties of pumice reinforced aluminum syntactic foams produced by cold chamber die casting

Foaming Behavior of AlMg4Si8 Matrix and Pure Al Matrix Precursors in Closed Cavities with Different TiH2 Addition Levels

Mechanical Properties of Foam Aluminum with Different Sizes

Experimental study and numerical prediction of tensile strength properties and failure modes of hollow spheres filled syntactic foams

The influence of pure Al and hypoeutectic Al Si alloy base materials on the cell structures of aluminum foams produced by gas injection foaming process

Microstructure and Compressive Properties of Inco-617 Alloy Hollow Sphere Foam