Abstract:Twins play an important role in the texture transition during annealing. In a cold rolled high rare earth content magnesium (Mg) alloys with {10–12} extension twins, {11–21} extension twins, {10–11} compression twins and {10–11}-{10–12} double twins and frequent twin-twin interactions, quasi-in-situ electron backscatter diffraction method was used to observe the twin induced static recrystallization (SRX) and related effect on texture during annealing. The results show that basal component was consumed owing to the SRX occurred in basal oriented {10–12} twins and SRXed grains with several specific orientations show preferential grain growth. SRX widely operated in the {10–12} extension and {11–21} extension twins, but absent in most {10–11} compression and {10–11}-{10–12} double twins, which is different to traditional twin induced SRX. Most compression/double twins detwinned while only partial tension twins detwinned. Operation of {11–21} twins and resultant twin-twin interaction facilitate the formation of serrated twin boundaries, which can serve as nucleation sites. Activation of 〈c + a〉 dislocation and related dislocation interaction in high dislocation density areas promote the formation of new grain boundaries and related SRX. Profuse 〈c + a〉 dislocations in basal oriented twins release the strain accumulation in compression/double twins and thus result in the absence of SRX. The twin size difference, storage energy and dislocation-twin interaction commonly functioned to the detwinning during annealing. The near-coincide site lattice boundaries that show high mobility were considered to be the important contributor to the preferential grain growth of SRXed grains.

Quasi-in-situ electron backscattered diffraction investigation of twin-induced recrystallization during electrical pulse treatment in AZ61 alloy

Microstructure and texture evolution of cold-rolled Mg-3Al-1Zn alloy by electropulse treatment stimulating recrystallization

Precipitation phase diffusion kinetics of AZ61 alloy under electrical pulse treatment

Twin recrystallization mechanisms in a high strain rate compressed Mg-Zn alloy

A Comparative Study on the Static Recrystallization Behavior of Cold-Rolled Mg-3Al-1Zn Alloy Stimulated by Electropulse Treatment and Conventional Heat Treatment

Microstructure and Texture Evolution of Magnesium Alloys During Electropulse Treatment

Mechanism of Electropulsing Induced Recrystallization in a Cold-Rolled Mg–9Al–1Zn Alloy

Microstructure and texture evolution of the cold-rolled AZ91 magnesium alloy strip under electropulsing treatment

Influence of Twinning-Induced Recrystallization on Texture Evolution in a High Strain Rate Compressed Mg-Zn Alloy

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Athermal influence of pulsed electric current on the twinning behavior of Mg-3Al-1Zn alloy during rolling

Effect of Electroplastic Treatment on Microstructure and Texture Changes of a Cold Rolling AZ31 Strip

Effect of Pulsed Current on the Tensile Deformation Behavior and Microstructure Evolution of AZ80 Magnesium Alloy

The Effect of Multiple Pulse Treatment on the Recrystallization Behavior of Mg-3al-1zn Alloy Strip

Recrystallization of bulk nanostructured magnesium alloy AZ31 after severe plastic deformation: an in situ diffraction study

Thermal and Electromigration Effects of Electropulsing on Dynamic Recrystallization in Mg–3Al–1Zn Alloy

Quasi-in Situ Electron Backscatter Diffraction Analysis of Twinning–detwinning Behavior in AZ31 Magnesium- Alloy Rolled Plates Subjected to Compression Loading in Different Directions

Unusual Twin Induced Recrystallization and Corresponding Texture Optimization in a Cold Rolled Mg-Gd-Zr Alloy During Annealing

Texture Modification of Magnesium Alloys During Electropulse Treatment

Dynamic recrystallization, twinning behaviors and mechanical response of pre-twinned AZ31 Mg alloy sheet along various strain paths at warm temperature

Application Study of High Energy Pulse Current in Rolling of AZ31 Magnesium Alloy