Abstract:Titanium aluminide (TiAl) alloys are promising high-temperature structural materials in the aerospace field. Additive manufacturing is a desirable process for fabricating TiAl alloys. In the process of wire arc additive manufacturing of TiAl alloys, Al-based and Ti-based wires were used as the feedstocks. However, it is hard to ensure the two different wires melt synchronously under the heat of one single arc, so the desired microstructures with gamma (TiAl) phase and alpha(2) (Ti3Al) phase are hard to obtain. A two-wire TOP-TIG-based additive manufacturing process for TiAl alloys is proposed in this paper. The Ti6Al4V wire and pure Al wire are used as the feedstocks. The Al wire is fed in TOP-TIG mode behind the molten pool, while the Ti6Al4V wire is fed in conventional TIG mode in front of the molten pool. The two wires melt synchronously in a broad range of parameters. The compositions of the component can be controlled by adjusting the two-wire feeding speeds. The main microstructures of the as-fabricated component contain alpha(2)/gamma lamellae colonies, equiaxed gamma grains, and alpha(2) grains. In the top and middle regions, when the Al content is 45 at.%, the structures are full alpha(2)/gamma lamellae; as the Al content increases to 50 at.%, some equiaxed gamma grains distribute at the grain boundaries; the component with 55 at.% Al content exhibits the structures consists of equiaxed gamma grains with snowflake-shaped alpha(2)/gamma lamellae colonies. In the bottom region, all components exhibit the coarse equiaxed alpha(2) grains with gamma laths. As the Al content increases, the alpha(2) phase decreases, but the gamma phase increases, and from the top region to the bottom region, the volume fraction of the alpha(2) increases by about 19.4 %. The hardness value of the top and bottom regions is higher, and the middle region exhibits the lowest hardness. As the Al content increases, the hardness decreases. The component with 50 at.% Al exhibits the highest compressive strength with 1762 MPa and the largest compressive ratio with 26.1%.

Twin-wire plasma arc additive manufacturing of the Ti–45Al titanium aluminide: Processing, microstructures and mechanical properties

Fabrication of γ-TiAl intermetallic alloy using the twin-wire plasma arc additive manufacturing process: Microstructure evolution and mechanical properties

Microstructure and Fatigue Properties of Ti-48Al Alloy Fabricated by the Twin-Wire Plasma Arc Additive Manufacturing

Effect of substrate temperature on microstructure and mechanical properties of TiAl alloy fabricated using the twin-wire plasma arc additive manufacturing system

Wire Arc Additive Manufacturing of Titanium Aluminide Alloys Using Two-Wire TOP-TIG Welding: Processing, Microstructures, and Mechanical Properties

Twin-wire Directed Energy Deposition-Arc of Ti–48Al–2Cr–2Nb Alloy: Feasibility, Microstructure, and Tensile Property Investigation

Microstructure Modification of Twin-Wire Directed Energy Deposition-Arc Fabricated Γ-Tial Alloy Via Deposition Current Control

Heat Accumulation, Microstructure Evolution, and Stress Distribution of Ti–Al Alloy Manufactured by Twin‐Wire Plasma Arc Additive

Fabrication of Titanium Aluminides via Powder-Cored Wire Arc Additive Manufacturing: Microstructural and Mechanical Characterization

Composition-induced microcrack defect formation in the twin-wire plasma arc additive manufacturing of binary TiAl alloy: An X-ray computed tomography-based investigation

Microstructural evolution and mechanical property of Ti-6Al-4V wall deposited by continuous plasma arc additive manufacturing without post heat treatment

Effect of droplet transfer mode on composition homogeneity of twin-wire plasma arc additively manufactured titanium aluminide

Research on high efficiency deposition method of titanium alloy based on double-hot-wire arc additive manufacturing and heat treatment

Modification of Microstructure and Mechanical Properties for Twin-Wire Directed Energy Deposition-Arc Fabricated Ti-48al-2cr-2nb Alloys Via Current Regulation

Fabrication of Titanium Aluminide Alloys by Twin-Wire Tungsten Inert Gas Welding Applied with High-Frequency Induction Heating Wire Technology: Processing, Microstructure, and Properties

Microstructure and mechanical properties of Ti-3Al-2V alloy by dual wire + arc additive manufacturing

A novel magnetic field assisted powder arc additive manufacturing for Ti60 titanium alloy: Method, microstructure and mechanical properties

Fabrication of Fe–30Al alloy using plasma arc welding powered twin-wire directed energy deposition-arc process: Droplet transfer, microstructure, and mechanical property investigation

Investigation on Heat Treatment Strategy Eliminating Heterogeneity and Anisotropy of TiAl Alloy Fabricated Using Twin-Wire Directed Energy Deposition-Arc

Microstructure Evaluation of the Potential of Additive Manufactured Dissimilar Titanium-Aluminum Alloys

In-situ neutron diffraction characterization on the phase evolution of γ-TiAl alloy during the wire-arc additive manufacturing process