Abstract:Due to the rapid heating-cooling process and unstable keyhole, pore defects are easily formed during the high energy beam-powder additive manufacturing (AM) process, posing great challenges to the high-performance manufacturing of aerospace components. Using an arc with lower energy density as a heat source can effectively avoid these defects, but its matching raw materials are limited to wire. In this paper, a novel magnetic field assisted powder arc additive manufacturing (MFA-PAAM) method has been proposed, which combines arc heat source and powder raw material to achieve dense metal parts. A transverse magnetic field (TMF) was introduced to solve the powder spattering problem which impacts the stability of the PAAM process, by regulating the direction of the arc plasma flow and the arc pressure. The unique melting behavior of the powder under arc heating was captured by a high-speed camera, which can be summarized into two steps: balling and adsorption by the molten pool. And the well-formed and fully dense Ti60 high-temperature titanium alloy wall components were successfully manufactured using the self-developed equipment. The microstructure of the thin-wall component is dominated by basket-weave distributed α laths and few β sheets remaining at their boundaries. A layered periodic distribution along the building direction was observed, which is mainly distinguished from the content and morphology of the β phase. The average ultimate tensile strength (UTS) and elongation to failure in the travelling direction are 1003.2 MPa and 15.1%, while the average UTS and elongation along the building direction are 1009.3 MPa and 16.6%, respectively. The fracture morphologies in both directions are characterized by ductile fracture. The MFA-PAAM technique shows great potential for fabricating materials that are difficult to be drawn into wires with high efficiency and performance.

A novel magnetic field assisted powder arc additive manufacturing for Ti60 titanium alloy: Method, microstructure and mechanical properties

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Microstructural evolution and mechanical property of Ti-6Al-4V wall deposited by continuous plasma arc additive manufacturing without post heat treatment

Electron Beam Welding and Post Heat Treatment of a New Near-Beta High-Strength Ti-4Al-5Mo-5V-5Cr-1Nb Alloy

A Review of Additive Manufacturing Techniques and Post-Processing for High-Temperature Titanium Alloys

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties

Numerical Simulation, Microstructure, and Properties of TC4 Plasma Arc Additive Manufactured Thin Wall

Mechanism of enhanced ductility of Ti–6Al–4V alloy components deposited by pulsed plasma arc additive manufacturing with gradient-changed heat inputs

Microstructure and Fatigue Properties of Ti-48Al Alloy Fabricated by the Twin-Wire Plasma Arc Additive Manufacturing

High-efficient hybrid arc and friction stir additive manufacturing of high-performance Al-Cu-Mg-Ag-Zr alloy: Microstructural evolution and precipitation behaviors with Ω/L1 2 co-precipitates

Fabrication of γ-TiAl intermetallic alloy using the twin-wire plasma arc additive manufacturing process: Microstructure evolution and mechanical properties

Controlling the Microstructure and Properties of Ti-6.5al-2zr-1mo-1v Components Fabricated by High-Deposition-Rate Wire Arc Additive Manufacturing

Ultrastrong nanotwinned titanium alloys through additive manufacturing

Research Viewpoint on Performance Enhancement for Very-High-Cycle Fatigue of Ti-6Al-4V Alloys via Laser-Based Powder Bed Fusion

Microstructure and Mechanical Properties of 600℃High Temperature Titanium Alloy Fabricated by Additive Manufacturing

In-situ fabrication of Ti<sub>2</sub>AlNb-based alloy through double-wire arc additive manufacturing

Short Circuiting Transfer, Formation, and Microstructure of Ti-6Al-4V Alloy by External Longitudinal Magnetic Field Hybrid Metal Inert Gas Welding Additive Manufacturing

Effect of substrate temperature on microstructure and mechanical properties of TiAl alloy fabricated using the twin-wire plasma arc additive manufacturing system

Enhanced mechanical properties of Ti6Al4V alloy fabricated by laser additive manufacturing under static magnetic field

Cost-affordable Ti-6Al-4V for Additive Manufacturing: Powder Modification, Compositional Modulation and Laser In-Situ Alloying

Heterogeneous microstructure evolution in Ti-6Al-4V alloy thin-wall components deposited by plasma arc additive manufacturing