Abstract:Due to the rapid heating-cooling process and unstable keyhole, pore defects are easily formed during the high energy beam-powder additive manufacturing (AM) process, posing great challenges to the high-performance manufacturing of aerospace components. Using an arc with lower energy density as a heat source can effectively avoid these defects, but its matching raw materials are limited to wire. In this paper, a novel magnetic field assisted powder arc additive manufacturing (MFA-PAAM) method has been proposed, which combines arc heat source and powder raw material to achieve dense metal parts. A transverse magnetic field (TMF) was introduced to solve the powder spattering problem which impacts the stability of the PAAM process, by regulating the direction of the arc plasma flow and the arc pressure. The unique melting behavior of the powder under arc heating was captured by a high-speed camera, which can be summarized into two steps: balling and adsorption by the molten pool. And the well-formed and fully dense Ti60 high-temperature titanium alloy wall components were successfully manufactured using the self-developed equipment. The microstructure of the thin-wall component is dominated by basket-weave distributed α laths and few β sheets remaining at their boundaries. A layered periodic distribution along the building direction was observed, which is mainly distinguished from the content and morphology of the β phase. The average ultimate tensile strength (UTS) and elongation to failure in the travelling direction are 1003.2 MPa and 15.1%, while the average UTS and elongation along the building direction are 1009.3 MPa and 16.6%, respectively. The fracture morphologies in both directions are characterized by ductile fracture. The MFA-PAAM technique shows great potential for fabricating materials that are difficult to be drawn into wires with high efficiency and performance.

High-efficient hybrid arc and friction stir additive manufacturing of high-performance Al-Cu-Mg-Ag-Zr alloy: Microstructural evolution and precipitation behaviors with Ω/L1 2 co-precipitates

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Superior strength of laser-arc hybrid additive manufactured Al-Zn-Mg-Cu alloy enabled by a tunable microstructure

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Achieving high strength-ductility of Al-Zn-Mg-Cu alloys via hot-wire arc additive manufacturing enabled by strengthening precipitates

Gradient microstructure and strength-ductility synergy improvement of 2319 aluminum alloys by hybrid additive manufacturing

Refined microstructure and enhanced mechanical performance of hybrid additive manufacturing Al-Cu-Mg alloys by multi-cycle friction stirring processing

Microstructure evolution and mechanical properties of wire-arc additive manufactured Al–Zn–Mg–Cu alloy assisted by interlayer friction stir processing

Enhanced Plastic Stability: Achieving High Performance in a Al6xxx Alloy Fabricated by Additive Manufacturing

Improvement of microstructure and fatigue performance of wire-arc additive manufactured 4043 aluminum alloy assisted by interlayer friction stir processing

Enhancing strength, ductility, and fatigue performance of Al-Zn-Mg-Cu-Sc-Zr alloy using a hybrid approach: Wire-arc directed energy deposition and interlayer friction stir processing

Formation mechanism of Al-Zn-Mg-Cu alloy fabricated by laser-arc hybrid additive manufacturing: Microstructure evaluation and mechanical properties

Microstructure and properties research of Al-Zn-Mg-Cu alloy with high strength and high elongation fabricated by wire arc additive manufacturing

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Minimizing porosity and optimizing microstructure of hot-wire arc additive manufactured Al-Cu-Mg-Ag alloy for strength increment

Microstructural modification and enhanced mechanical properties of wire-arc additive manufactured 6061 aluminum alloy via interlayer friction stir processing

Achieving high performance of wire arc additive manufactured Mg–Y–Nd alloy assisted by interlayer friction stir processing

Tailoring the microstructure and mechanical properties of wire and arc additive manufactured Al-Mg alloy via interlayer friction stir processing

A novel magnetic field assisted powder arc additive manufacturing for Ti60 titanium alloy: Method, microstructure and mechanical properties

Enhanced strength-plasticity of 2319 Al-Cu alloy formed by hybrid interlayer friction stir processing and wire-arc additive manufacturing

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT