Abstract:To reduce carbon emissions associated with substantial concrete usage in construction and achieve the objectives of green and low-carbon construction, this study innovatively develops a low-carbon binary material by adding limestone powder (LP) and silica fume (SF) into the conventional cement-based material, enhancing the comprehensive utility value of LP. The experimental results show that the addition of 15% LP and 5% SF increases the yield stress of the mortar yet substantially reduces the plastic viscosity to 2.84 Nmm·min, representing a 44.5% decrease compared to pure cement slurry. This reduction is conducive to long-distance pumping of the cement-based material. Moreover, the addition of 5% SF compensates for the 18.8% (mid-stage, 28-d) and 15.8% (late-stage, 90-d) strength loss in mortar caused by LP while simultaneously improving the strength of the co-mixed system by 10.4% (mid-stage) and 10.8% (late-stage). In the early-stage measurements of the LP-SF binary cement-based materials, it is observed that while SF slightly increases the hydration heat release, LP suppresses the early hydration heat release. Therefore, the total heat release observed in the 15% LP and 5% SF group after 72 h is only 254 J/g, demonstrating favorable temperature control and crack prevention effects. In addition, X-ray diffraction (XRD) and thermogravimetric/differential thermogravimetric (TG/DTG) phase analysis reveal a notable increase of 53.56% in CH consumption. Besides, the weight loss on ignition of C-S-H crystals increases, indicating that the secondary hydration of LP and the pozzolanic reaction of SF promote the production of C-S-H in the system. Combined with the late-stage strength and water absorption characteristics, it is concluded that the system exhibits good mechanical properties and compactness. This study presents a use of mixed proportion that enables excellent mechanical properties, good pumping performance, and low hydration heat. Moreover, the analysis indicates that the carbon emission of each cubic meter of the as-developed mortar is reduced by approximately 16.7–23.9%, promoting the efficient and clean utilization of LP and SF.

Hydraulic-lime based concrete: Strength development using a pozzolanic addition and different curing conditions

Experimental study on strength and abrasion-resistance enhancement admixture

Influence of Pozzolan, Slag and Recycled Aggregates on the Mechanical and Durability Properties of Low Cement Concrete

Effect of Thermoactivated Recycled Cement, Hardened Cement Powder and Hydrated Lime on the Compressive Strength of Mortars

Effects of Percentages and Effective Cementitious Coefficient of Zeolite and Silica Fume on the Compressive Strength and Water Absorption of Concrete

Adding hydrated lime for improving microstructure and mechanical properties of mortar for ultra-high performance concrete

Concrete Mix Strength and Permeability with Various Supplementary Cementitious Materials

Long-term Compressive Strength Properties of Concrete Incorporating Admixtures: Outdoor Exposure Testing in a Coastal Environment

Development of lime-pozzolan green binder: The influence of anhydrous gypsum and high ambient temperature curing

Effect of Mineral Aggregates and Chemical Admixtures as Internal Curing Agents on the Mechanical Properties and Durability of High-Performance Concrete

Experimental study on the mechanical behavior of concrete incorporating fly ash and marble powder waste

Compressive, flexural and splitting strength of fly ash and silica fume concrete

Investigation of self-compacting concrete utilizing different supplementary pozzolanic materials for cement replacement

Study on the Mechanical Properties of Two General-Purpose Cement–Lime Mortars Prepared Based on Air Lime

Examining the early-stage performance and mechanical performance of limestone powder-silica fume binary cement-based materials

Hydration, mechanical properties and durability of high-strength concrete under different curing conditions

Influence of High-Volume Mineral Mixtures and the Steam-Curing Temperatures on the Properties of Precast Concrete

Influence of Hydrated Lime on the Chloride-Induced Reinforcement Corrosion in Eco-Efficient Concretes Made with High-Volume Fly Ash

Production of an eco-friendly concrete by including high-volume zeolitic supplementary cementitious materials and quicklime

Estimating service life of reinforced concrete structures with binders containing silica fume and metakaolin under chloride environment: durability indicators and probabilistic assessment

Investigation on Mechanical Strength of Cellular Concrete in Presence of Silica Fume