Abstract:The microstructure, phase composition, precipitates evaluation, casting, and mechanical properties of the novel cast Al-4Cu-2.1Er-1Mg-0.2Zr-0.2Cr-0.15Fe-0.15Si-0.1Ti alloy were analyzed using by optical microscope, scanning and transmission electron microscopes, differential scanning calorimetry, thermodynamic calculations, hot cracking and mechanical properties measurements. The positive effect of Cr as a substitution of Mn on plasticity and precipitation strengthening was demonstrated. The 0.2Zr, 0.2Cr and 0.1 Ti as a grain refiners provide a fine grain size of 25 μm in the as-cast state due to primary Al 75–80 Cu 10–12 Er 3–4 Cr 7 phase particles formation as a nucleation centers of Al. The hot cracking index (HCI) of the AlCuErMgCr alloy was 12–14 mm which is similar with HCI of the cast Al-Si-Cu-Mg alloys. The good casting properties in the AlCuErMgCr alloy achieved due to a fine grain structure and narrow solidification range. The contribution of the Al 3 (Zr,Er) (40 nm), Al 45 Cr 7 (6 nm), and S'(θ') (100/5 nm) precipitates is 38.5 MPa, 140.4 MPa, and 198.9 MPa and the calculated contribution from dislocation and precipitates is 262.3 MPa. The ultimate tensile strength (UTS) and elongation (El.) of the AlCuErMgCr alloy are 372 MPa and 6% which is higher in 16.6% and 150%, respectively, than in the Mn-containing alloy. Novel alloy has an excellent combination of yield strength (YS) and plasticity at 20–250°C. The YS and El. are 301 MPa and 6% and 225–250 MPa and 4.6–11.5% at 20 and 200–250°C, respectively. The rupture strength at 250°C after 100 h ( σ100250 ) is 106 MPa. Mechanical and casting properties of the novel alloy are superior to the properties of commercial 201.0 (Al-Cu-Mn-Mg-Ag-Ti) alloy.

Influence of deformation and annealing on the structure, electrical resistance and hardness of the Al–4 %Cu–3 %Mn alloy casted in an electromagnetic crystallizer

The Impact of Thermomechanical Treatment on Structure, Electrical Resistance and Hardness of Al–4% Cu–3% Mn Alloy Casted in an Electromagnetic Crystallizer

The influence of Cu additions on the microstructure and properties of Al–Fe system alloys produced by casting into electromagnetic crystallizer

The Deformation Behavior and Microstructure Evolution of a Mn- and Cr-Containing Al-Mg-Si-Cu Alloy During Hot Compression and Subsequent Heat Treatment

Influence of deformation on the structure and the mechanical properties of a high-entropy Fe25Cr20Ni20Co10Mn15Al10 alloy

Evolution of the microstructure and properties of a Cu–Cr-(Mg) Alloy upon thermomechanical treatment

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Microstructure evolution and property strengthening of CuCr50 prepared by thermite reduction-electromagnetic casting during the heat treatment process

Effects of Thermal Variables of Solidification on the Microstructure and Hardness of the Manganese Bronze Alloy Cu-24Zn-6Al-4Mn-3Fe

The Effects of a Trace Amount of Manganese and the Homogenization on the Recrystallization of Al–7Mg–0.15Ti Alloys

Simultaneous Increase of Electrical Conductivity and Hardness of Al–1.5 wt.% Mn Alloy by Addition of 1.5 wt.% Cu and 0.5 wt.% Zr

Influence of Alloying Elements on the Dynamic Recrystallization of 4 wt.-% Medium Manganese Steels

Effect of Fe and Si on the Phase Composition and Microstructure Evolution in Al-2 wt.% Cu-2 wt.% Mn Alloy During Solidification, Cold Rolling and Annealing

Effect of Mn‐bearing dispersoids on tensile properties and recrystallization resistance of Al‐3Mg‐0.8Mn rolled alloy

Influence of intermetallics and element concentrations on the performance of the heat treated HVDC AlSiMgMnCu alloys at nano-scale

Study of the effect of calcium on structure, physicomechanical and technological properties of deformable alloy Al-3%Mg-0.8%Mn

Effect of Mechanical Alloying on the Dissolution of the Elemental Mn and Al-Mn Compound in Aluminum

Effect of Mn substitution on Cr in the Al-Cu-Er-Mg-Zr-Fe-Si-Ti cast alloy

Microstructure evolution of a novel low-silicon cast aluminum alloy modified with Mn and Cr during solution treatment

Influence of the Al Content on the Properties of Mechanically Alloyed CoCrFeNiMnXAl20-X High-Entropy Alloys