Abstract:Al-Mn-Fe-Si strips were fabricated via both the twin-roll casting (TRC) and the more conventional route, direct-chill casting (DC). The two types of strips prepared were subjected to thermal exposure at a series of temperatures. Uniaxial tensile tests after the thermal exposure showed that while the DC strip presented a-74% decrease in the yield strength and-35% decrease in the ultimate tensile strength (UTS) after being exposed to 350 degrees C for 12 h, the TRC strip, in contrast, maintained its strength at temperatures up to-460 degrees C for the same duration. Systematic microstructure characterization revealed that the different thermal stability in the strength of the two types of strips arised from their distinct evolution in grain morphology and second phase particles during the thermal exposure. The calculation based on Cahn-Lucke-Stuwe (CLS) model suggested that due to the highly supersaturated solute atoms, at the beginning of the thermal exposure, the TRC strip experienced a strong solute drag which reduced the grain boundary migrating velocity to a value that is orders of magnitude smaller than that in the DC strip. With the progress of the thermal exposure, the solute atoms precipitated out, forming densely distributed second phase particles. For one thing, these particles stabilized the grain structure by inducing Zener pinning pressure which could be ten times higher than that in the DC strip, depending on the temperature. For another, they acted as dislocation obstacles and compensated for the strength loss owing to decreasing solution hardening. Both effects contributed to the TRC strip's fairly stable strength regarding thermal exposure below 460 degrees C. The present work could guide the direct application of the TRC strips in the industry. The results should also be helpful for the development of a fundamental framework for designing advanced TRC Al strips with improved mechanical properties at elevated temperatures. (c) 2022 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

The Impact of Thermomechanical Treatment on Structure, Electrical Resistance and Hardness of Al–4% Cu–3% Mn Alloy Casted in an Electromagnetic Crystallizer

Influence of deformation and annealing on the structure, electrical resistance and hardness of the Al–4 %Cu–3 %Mn alloy casted in an electromagnetic crystallizer

Microstructure evolution and property strengthening of CuCr50 prepared by thermite reduction-electromagnetic casting during the heat treatment process

EFFECTS OF THERMAL MECHANICAL TREATMENT ON THE MICROSTRUCTURES AND HARDNESS OF AN Al-Zn-Mg-Cu ALLOY PLATE

Effect of heat treatment on microstructure and mechanical properties of Cu–6.9Ni–2.97Al–0.99Fe–1.06Mn alloy

The influence of Cu additions on the microstructure and properties of Al–Fe system alloys produced by casting into electromagnetic crystallizer

Evolution of the microstructure and properties of a Cu–Cr-(Mg) Alloy upon thermomechanical treatment

Effects of Thermal Variables of Solidification on the Microstructure and Hardness of the Manganese Bronze Alloy Cu-24Zn-6Al-4Mn-3Fe

The Effects of a Trace Amount of Manganese and the Homogenization on the Recrystallization of Al–7Mg–0.15Ti Alloys

The effects of solution heat treatment on the microstructure and hardness of an aluminum-4% copper alloy with added nickel and tin

Effect of Solution Heat Treatment on Microstructure and some Properties of Al–Cu–Mg Alloy

Evolution of microstructure, mechanical properties and corrosion behavior of Al-4Mg-2Zn-0.3Ag (wt.%) alloy processed by T6 or thermomechanical treatment

Simultaneous Increase of Electrical Conductivity and Hardness of Al–1.5 wt.% Mn Alloy by Addition of 1.5 wt.% Cu and 0.5 wt.% Zr

Thermal and Barothermal Treatment, Microstructure, and Properties of an Al–8Si–3.5Cu–0.2Mn Alloy

Effect of Heat Treatment on Microstructure, Mechanical, and Corrosion Properties of Squeeze Cast Al 319.0 Alloy

Influence of intermetallics and element concentrations on the performance of the heat treated HVDC AlSiMgMnCu alloys at nano-scale

Impact of Thermal Exposure on the Microstructure and Mechanical Properties of a Twin-Roll Cast Al-Mn-Fe-Si Strip

Effect of Final Thermomechanical Treatment on the Mechanical Properties and Microstructure of T Phase Hardened Al-5.8Mg-4.5Zn-0.5Cu Alloy

CALPHAD Simulation and Experimental Study on Heat Treatment Process of Al-Cu-Mn-Mg-Sc Cast Alloys

Effect of Solution Treatment on Microstructures and Mechanical Properties of Centrifugal Casting Al-Cu Alloy

Microstructure and Mechanical Properties of High-Carbon-Containing Fe-Ni-Mn-Al-Cr High-Entropy Alloy: Effect of Thermomechanical Treatment