Abstract:The microstructure, phase composition, precipitates evaluation, casting, and mechanical properties of the novel cast Al-4Cu-2.1Er-1Mg-0.2Zr-0.2Cr-0.15Fe-0.15Si-0.1Ti alloy were analyzed using by optical microscope, scanning and transmission electron microscopes, differential scanning calorimetry, thermodynamic calculations, hot cracking and mechanical properties measurements. The positive effect of Cr as a substitution of Mn on plasticity and precipitation strengthening was demonstrated. The 0.2Zr, 0.2Cr and 0.1 Ti as a grain refiners provide a fine grain size of 25 μm in the as-cast state due to primary Al 75–80 Cu 10–12 Er 3–4 Cr 7 phase particles formation as a nucleation centers of Al. The hot cracking index (HCI) of the AlCuErMgCr alloy was 12–14 mm which is similar with HCI of the cast Al-Si-Cu-Mg alloys. The good casting properties in the AlCuErMgCr alloy achieved due to a fine grain structure and narrow solidification range. The contribution of the Al 3 (Zr,Er) (40 nm), Al 45 Cr 7 (6 nm), and S'(θ') (100/5 nm) precipitates is 38.5 MPa, 140.4 MPa, and 198.9 MPa and the calculated contribution from dislocation and precipitates is 262.3 MPa. The ultimate tensile strength (UTS) and elongation (El.) of the AlCuErMgCr alloy are 372 MPa and 6% which is higher in 16.6% and 150%, respectively, than in the Mn-containing alloy. Novel alloy has an excellent combination of yield strength (YS) and plasticity at 20–250°C. The YS and El. are 301 MPa and 6% and 225–250 MPa and 4.6–11.5% at 20 and 200–250°C, respectively. The rupture strength at 250°C after 100 h ( σ100250 ) is 106 MPa. Mechanical and casting properties of the novel alloy are superior to the properties of commercial 201.0 (Al-Cu-Mn-Mg-Ag-Ti) alloy.

Simultaneous Increase of Electrical Conductivity and Hardness of Al–1.5 wt.% Mn Alloy by Addition of 1.5 wt.% Cu and 0.5 wt.% Zr

Improved Strength and Enhanced Pitting Corrosion Resistance of Al-Mn Alloy with Zr Addition

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Coupling Effect of Mn Addition and Deformation on Mechanical and Electrical Properties of Al-Zr Alloys

Simultaneously improving mechanical properties and electrical conductivity of Al-1.9Mn alloys with different Mg and Si addition

Effects of Cr and Zr additions on the microstructure and properties of Cu-6wt.% Ag alloys

Influence of Zr and Mn additions on microstructure and properties of Mg—2.5wt%Cu—Xwt%Zn (X = 2.5, 5 and 6.5) alloys

Multi-alloying effect of Ti, Mn, Cr, Zr, Er on the cast Al-Zn-Mg-Cu alloys

Microstructure and Mechanical Properties of As-Cast Al-10Ce-3Mg-xZn Alloys

Phase Composition and Structure of Al–Cu–Mn–Mg–Zn–Fe–Si Alloys Containing 2% Cu and 1.5% Mn

Effect of Mn Element Addition on the Microstructure, Mechanical Properties, and Corrosion Properties of Mg-3Zn-0.2Ca Alloy

Effect of Mn substitution on Cr in the Al-Cu-Er-Mg-Zr-Fe-Si-Ti cast alloy

Influence of Mn Addition on the Evolution of Precipitates in Al-Cu Alloys

Microstructure and properties of a novel ultra-high strength, high elasticity and high plasticity Cu–20Ni–20Mn-0.3Nb-0.3Cr-0.1Zr alloy

The role of Sn trace addition in the precipitation behavior and strengthening of the wrought Al–Cu–Mn-based alloy

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Influence of deformation and annealing on the structure, electrical resistance and hardness of the Al–4 %Cu–3 %Mn alloy casted in an electromagnetic crystallizer

Effects of Al addition on corrosion behavior and mechanical property of high-strength and high-elasticity Cu-20Ni-20Mn-0.3Nb-0.3Cr-0.3Zr alloy

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Microstructure and Properties of High Strength and High Conductivity Cu-0.4Mg Alloy Processed by Upward Continuous Casting and Multi-pass Drawing

The development of low-temperature heat-treatable high-pressure die-cast Al–Mg–Fe–Mn alloys with Zn