Abstract:The microstructure evolution of Mg-3Sn, Mg-3Sn-3Al-Zn (ATZ331), and Mg-3Sn-6Al-Zn (ATZ631) alloys during high-speed rolling (HSR) and annealing was studied. High-speed rolling was carried out on the three alloys at a rolling speed of 1100 m/min, a rolling temperature of 400 °C, and a reduction of 40% during a single pass. The results showed that the microstructure of the samples after HSR contained many twins and was dominated by {10−12} extension twins (ETs) and supplemented by {10−11} contraction twins (CTs) and {10−11}-{10−12} double twins (DTs). After adding Al, the content of these different types of twins was reduced. The twinning fraction decreased significantly with 3 wt% Al addition, while the twinning fraction decreased slightly with 6 wt% Al addition. The high-speed rolled alloys were annealed at 370 °C for 1 min, 2 min, 3 min, 5 min, and 8 min. When the annealing time was 1 min, the recrystallization fraction of the ATZ631 alloy was low, indicating that increasing the Al content to 6 wt% inhibited recrystallization. When the annealing time increased to 3 min, the recrystallized grains in the ATZ631 alloy grew, indicating that the grain growth progressed faster in this alloy. When the annealing time was 8 min, the grain size of the three alloys grew. The electron backscattered diffraction (EBSD) results of the alloy annealed for 8 min showed that the twin fraction in the annealed state was lower than that after high-speed rolling. In addition with the increase in Al content, the twin fraction decreased. During high-speed rolling, the maximum intensity also increased with an increase in Al content, were 22.72, 25.09, and 26.35, and the texture of the annealed alloy was weakened. The Al addition also increased the maximum intensity.

Effect of Mn‐bearing dispersoids on tensile properties and recrystallization resistance of Al‐3Mg‐0.8Mn rolled alloy

Achieving superior dispersion-strengthening effect in an AA5xxx Al-Mg-Mn alloy by mico-alloying

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Study of the effect of calcium on structure, physicomechanical and technological properties of deformable alloy Al-3%Mg-0.8%Mn

Quantitative analysis of influence of α-Al(MnFeCr)Si dispersoids on hot deformation and microstructural evolution of Al-Mg-Si alloys

Non-basal Slips Mediated Dynamic Recrystallization Promote Synergistic Strengthening and Toughening of Centrifugal Casting Mg–1.1Mn–0.5Al Alloy via High Strain Rolling

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Effect of recrystallization annealing, solid solution and pre-aging intermediate treatment on microstructure and mechanical properties of Al-Mg-Si rolled sheet

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Enhancing mechanical properties of twin-roll cast Al–Mg–Si–Fe alloys by regulating Fe-bearing phases and macro-segregation

Improving Mechanical Properties of Mg-Al-RE Alloys with the Formed Dimples of Al10Mn2RE Particles and Activated Pyramidal Slip with Mn Additions

Effect of Al addition and annealing on the microstructure evolution of Mg-3Sn Mg alloy subjected to high-speed rolling

Effect of Al on the Microstructure and Mechanical Properties of Mg–Sn–Ca–Mn Wrought Alloy

Synergistic effects of Cd, Si and Cr additions on precipitation strengthening and thermal stability of dispersoids in AA3003 alloy

Influence of Different Rolling Processes on Microstructure and Strength of the Al–Cu–Li Alloy AA2195

Understanding effect of Mg and Mn equivalents on columnar-to-equiaxed transition of high-strength Al alloy fabricated by laser powder bed fusion

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Effect of transition elements on dispersoid formation and elevated-temperature mechanical properties in 6082 aluminum alloy

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Effect of Mn content on the microstructure and mechanical properties of as-extruded Zn-0.2Mg-Mn (wt%) alloys