Abstract:Tunnel-type (T-type) Na0.44MnO2 (NMO) is a promising cathode material for sodium-ion batteries (SIBs) owing to its high rate performance and cycling stability compared to manganese-based layered oxides. However, the low specific capacity still restricts its practical applications. Herein, a Co-doped T-type NMO is synthesized through a facile solid-state reaction method and utilized as a cathode material for SIBs. A T-type Na0.44Mn0.9925Co0.0075O2 (NMO-3) electrode can deliver a high reversible capacity of 138 mAh g–1 at 0.1C, a superior rate capability (133, 130, 121, 106, and 93 mAh g–1 at 0.5, 1, 2, 5, and 10C, respectively), and excellent cycling stability (85.2% at 10C after 500 cycles). The substitution of Co3+ by Mn3+ leads to the enlargement of small and S-shaped tunnel spaces, which facilitates the insertion/deinsertion of Na+ into/from NMO-3 and greatly enhances its rate capability and cycling stability. Moreover, the reduced energy barriers for Na+ diffusion in small tunnels make the inactive Na+ easier to be deintercalated, which should be responsible for its high specific capacity that exceeds the theoretical capacity of T-type NMO.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c13278?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c13278</a>.XRD patterns and Rietveld refinement plot (Figure S1); XPS patterns of Mn 2p and Co 2p (Figure S2); SEM, TEM, and HRTEM images (Figure S3); CV curves (Figure S4); charge–discharge profile of the initial three cycles (Figure S5); CV curves at different scanning rates (Figure S6); SEM images after 100, 300, and 500 cycles (Figure S7); Nyquist plots before and after cycling (Figure S8); evolution of lattice parameters obtained by in situ XRD (Figure S9); assembly drawing of the in situ XRD cell (Figure S10); formation energies with different Co-substitution contents (Figure S11); structure evolutions and energy barriers (Figure S12); TEM-HAADF and TEM-EDX element mapping images at a fully charged state (Figure 13); electronic conductivities (Figure S14); lattice parameters from Rietveld refinement (Table S1); ICP-OES (Table S2); content of Mn3+ and Mn4+ (Table S3); dissolution degree of Mn after cycling (Table S4); impedance parameters before cycling (Table S5); impedance parameters after cycling (Table S6); comparison of electrochemical properties (Table S7); and potential of redox peaks by CV curves (Table S8) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c13278/suppl_file/am0c13278_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Lattice regulation strategy for constructing high-rate performance Na0.44Mn0.895Ti0.1Mg0.005O2 sodium-ion batteries cathode materials

Structural Insight into the Abnormal Capacity of a Co-Substituted Tunnel-Type Na 0.44 MnO 2 Cathode for Sodium-Ion Batteries

High Performance Sodium-Ion Full Battery Based on One-Dimensional Nanostructures: the Case of Na0.44MnO2 Cathode and MoS2 Anode

Effect of Ti doping on the structural and electrochemical performance of O3-type Na(Ni0.3Fe0.2Mn0.5)1-xTixO2 cathode materials for sodium-ion batteries

Modulating the Electrochemical Performances of Layered Cathode Materials for Sodium Ion Batteries through Tuning Coulombic Repulsion between Negatively Charged TMO 2 Slabs.

Stable Electrochemical Properties of Titanium Doped LayeredP2-Type Na0.67Ni0.15 Mn0.85O2 Cathode Material for Sodium IonBatteriesH

Trace Ti/Mg Co-Doped O3-type Layered Oxide Cathodes with Enhanced Kinetics and Stability for Sodium-Ion Batteries

Entropy Strategy for Stabilizing O′3-NaMnO2-Layered Cathodes for Sodium-Ion Batteries

Structural Regulation of P2‐Type Layered Oxide with Anion/Cation Codoping Strategy for Sodium‐Ion Batteries

Ti, F Codoped Sodium Manganate of Layered P2-Na 0.7 MnO 2.05 Cathode for High Capacity and Long-Life Sodium-Ion Battery

High-Operating Voltage, Long-Life Layered Oxides for Sodium Ion Batteries Enabled by Cosubstitution of Titanium and Magnesium

Modulating Valence Electrons and Na Occupancy in Layered Cathodes for High-Performance Na-Ion Batteries

Zr-doped O3-type NaNi1/3Fe1/3Mn1/3O2 Cathodes with Enhanced Structure Stability for Sodium-Ion Batteries

Enhanced electrochemical performance of Na0.9Li0.1Mn0.9O2 by MgO coating for sodium-ion batteries

Insights into unrevealing the effects of the monovalent cation substituted tunnel-type cathode for high-performance sodium-ion batteries

High-voltage stability of O3-type sodium layered cathode enabled by preferred occupation of Na in the OP2 phase

Optimal Ti-Substitution in Layered Oxide Cathodes for Na-Ion Batteries

Manipulating Stable Layered P2‐Type Cathode via a Co‐Substitution Strategy for High Performance Sodium Ion Batteries

Synergistic Effect of Polymorphs in Doped NaNi0.5Mn0.5O2 Cathode Material for Improving Electrochemical Performances in Na-Batteries

Unraveling the Synergistic Effect of Mg and Ti Codoping to Realize an Ordered Structure and Excellent Performance for Sodium-Ion Batteries

Cation-Modified Anionic Redox Mechanism for High-Performance Layered Oxide As Sodium-Ion Batteries Cathode Material