Abstract:As the most basic interconnection metallic material, copper (Cu) has been widely used in giant-large scale integrated circuits (GLSI). Corrosion inhibitors always play a crucial role in the Cu chemical mechanical polishing (CMP) process. The passivation of hydrogen peroxide (H2O2) alone is too weak to adequately protect against chemical corrosion on the surface of Cu film, thus, it is necessary to add corrosion inhibitors to the slurry. As a representative corrosion inhibitor, 1, 2, 4-triazole was compared with a novel corrosion inhibitor known as TT-LYK (ethanol, 2, 2′-[[(methyl-1H-benzotriazol-1-yl) methyl] imino] bis-), and their mixed inhibitor was studied in this paper. Different analytical methods such as the potentiodynamic polarization test, physical appearance phenomenon analysis, contact angle measurement and dynamic polishing experiment were used to compare their inhibition properties, and the fitting of different adsorption isotherms and static erosion tests were used to clarify the adsorption types and passivation processes respectively. The results indicated that both TT-LYK and 1, 2, 4-triazole achieved the goal of inhibiting Cu surface corrosion, but the inhibition effect of TT-LYK was slightly weaker at the same mass fraction. The corrosion protection of the two inhibitors is mainly attributable to the presence of organic inhibitor molecules on the surface of Cu by chemisorption and physisorption simultaneously. The passivation processes of both can be divided into two steps. First, the direct growth of the Cu-inhibitor passivation film occurs, followed by the redeposition of the Cu-inhibitor complex. From the results of electrochemical experiments, it can be concluded that the structure of the thin passivation film growing on the Cu surface varies with the inhibitor, and the composition of the passivation film was investigated by XPS and Raman spectrum analysis. At the same time, the surface roughness after polishing was found to decrease with the increase in inhibition effect of the inhibitors. According to the inhibition characteristics of these two inhibitors, a mixed corrosion inhibitor (TT-LYK and 1, 2, 4-triazole) was proposed in this study. Under the synergistic inhibition action, better inhibition effect and surface quality for Cu CMP were obtained. This outcome may be ascribed to the variation in the structure and density of the passivation film.

Controllable adjustment of Ta and Cu material removal rate in TSV tantalum-based barrier layer planarization process

Barrier And Low K Polish With A Novel Alkaline Barrier Slurry Combining With Fa/O Chelating Agent

The role of formamidine acetate as a complexing agent in the chemical mechanical polishing process of Ta-based barrier layers for through-silicon vias wafers

Effect of 2-phosphonobutane-1,2,4-tricarboxylic acid (PBTCA) on Cu/Ta chemical mechanical planarization (CMP) in the barrier layer: A novel complexing agent and the dual role on Cu

Achieving equivalent removal of Ta and Ru via controlling oxidation for chemical mechanical polishing of advanced barrier layer

An Efficient and High Quality Chemical Mechanical Polishing Method for Copper Surface in 3D TSV Integration

Chemical Mechanical Polishing of Inlaid Copper Structures with Ru/Ta/TaN As Barrier/Liner Layer

Improvement of Via Dishing and Non-Uniformity in TSV Chemical Mechanical Planarization

Non-uniformity and Removal Rate Selectivity Investigations in Through Silicon Via Front Side CMP

Copper Chemical Mechanical Polishing and Wafer Thinning with Temporary Bonding for Through Silicon Via Interconnect

Experimental and computational studies on TAD as an additive of copper chemical mechanical polishing

The Cmp Effect Of Potassium Molybdate With Bta As Compound Corrosion Inhibitor Used In Cmp Of The Tsv Heterogeneous Microstructure

TSV CMP process optimization and dishing defect reduction

The Effect of Inhibitors on the Electrochemical Deposition of Copper Through-silicon Via and its CMP Process Optimization

Electrolyte Composition and Removal Mechanism of Cu Electrochemical Mechanical Polishing

Chemical mechanical polishing for copper films in integrated circuit wiring layers using an advanced slurry

Study on the film forming mechanism, corrosion inhibition effect and synergistic action of two different inhibitors on copper surface chemical mechanical polishing for GLSI

Interaction mechanism of Al2O3 abrasive in tantalum chemical mechanical polishing

Improvement in chemical mechanical polishing of 4H-SiC wafer by activating persulfate through the synergistic effect of UV and TiO2

Mechanism of 1,2,4-Triazole During Copper Chemical Mechanical Planarization

The Behaviours of BTA and SDS in the Alkaline Slurry during the Backside CMP of Heterogeneous Microstructure of TSV Wafers