Abstract:Using additives to adjust the morphology of perovskite films is an effective method to improve the power conversion efficiency (PCE) and long-term stability of CsPbIBr2 perovskite solar cells (PSCs). In this work, CsPbIBr2 films are modified with the guanidinium thiocyanate (GuaSCN) additive. After adding GuaSCN into the precursor of perovskite, the crystal quality of the resulted perovskite films improved, and the orientations of the (100) and (200) crystal planes are enhanced obviously. The energy level alignment is optimized, which is beneficial to the extraction of electrons. Moreover, the defect density is reduced, and the charge recombination process is effectively suppressed, thereby improving the solar cell efficiency and stability. GuaSCN is absent from the resulted perovskite film due to the high-temperature annealing. Consequently, based on the GuaSCN additive with a 3% molar ratio in the perovskite precursor solution, the device yields a champion PCE of 10.90%, with an open-circuit voltage of 1.23 V, a short-circuit current of 12.05 mA/cm2, and a fill factor of 73.71%, which is 18.7% higher than that of the counterpart without GuaSCN. The improved CsPbIBr2 PSC shows better stability. The PCE retains ∼95% of its initial value compared to only ∼64% for pristine PSCs after being stored for over 600 h without encapsulation in air. This work provides a facile strategy for reducing defects and improving the performance of all-inorganic PSCs.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c03733.Experimental details; Tauc plots of the CPIB and CPIB-0.03 films; lifetime parameters derived from the TRPL spectroscopy; detailed photovoltaic parameters; J–V curves under reverse and forward scan directions; a brief summary of the photovoltaic parameters in high-efficiency CsPbIBr2 PSCs; EIS parameters; XPS spectra of Cs 3d, Pb 4f, I 3d, and Br 3d in the CPIB and CPIB-0.03 films; and photographs of the CPIB and CPIB-0.03 films at 20 °C, 50% RH (PDF)This article has not yet been cited by other publications.

Guanidinium iodide modification enabled highly efficient and stable all-inorganic CsPbBr3 perovskite solar cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Multifunctional Molecule Modification toward Efficient Carbon‐Based All‐Inorganic CsPbIBr 2 Perovskite Solar Cells

Guanidinium Thiocyanate Additive Engineering for High-Performance CsPbIBr 2 Solar Cells with an Efficiency of 10.90%

Secondary Crystallization Strategy for Highly Efficient Inorganic CsPbI2Br Perovskite Solar Cells with Efficiency Approaching 17％

First Investigation of Additive Engineering for Highly Efficient Cs2AgBiBr6-based Lead-Free Inorganic Perovskite Solar Cells

Intermediate‐Adduct‐Assisted Growth of Stable CsPbI 2 Br Inorganic Perovskite Films for High‐Efficiency Semitransparent Solar Cells

Gadolinium-incorporated CsPbI2Br for boosting efficiency and long-term stability of all-inorganic perovskite solar cells

Phase transition induced recrystallization and low surface potential barrier leading to 10.91%-efficient CsPbBr3 perovskite solar cells

Synergistic passivation and energy level alignment by graphene quantum dots for high performance inverted CsPbI3 perovskite solar cells

Carbon-Based Stable CsPbIBr 2 Solar Cells with Efficiency of over 10% from Bifunctional Quinoline Sulfate Modification

Optimizing the working mechanism of the CsPbBr3-based inorganic perovskite solar cells for enhanced efficiency

n-type absorber by Cd2+ doping achieves high-performance carbon-based CsPbIBr2 perovskite solar cells

High Efficiency (16.37%) of Cesium Bromide—Passivated All‐Inorganic CsPbI2Br Perovskite Solar Cells

Manipulating the Crystallization and Phase Transition for High-Performance CsPbI<sub>2</sub>Br Solar Cells

Dual interfacial modification to improve the performance of CsPbBr3 perovskite solar cells

Hydrophobic Organic Ammonium Halide Modification toward Highly Efficient and Stable CsPbI 2.25 Br 0.75 Solar Cell

Boosting the performance of low-temperature processed CsPbI2Br planar perovskite solar cells by interface engineering

Significant performance enhancement of all‐inorganic CsPbBr 3 perovskite solar cells enabled by Nb‐doped SnO 2 as effective electron transport layer

The sulfur-rich small molecule boosts the efficiency of carbon-based CsPbI2Br perovskite solar cells to approaching 14%

Surface passivation and hole extraction: Bifunctional interfacial engineering toward high-performance all-inorganic CsPbIBr 2 perovskite solar cells with efficiency exceeding 12%