Abstract:Composites that use fly ash and slag as alkali-activated materials instead of cement can overcome the defects and negative effects of alkali-activated cementitious materials prepared with the use of an alkali-activated material. In this study, fly ash and slag were used as raw materials to prepare alkali-activated composite cementitious materials. Experimental studies were carried out on the effects of the slag content, activator concentration and curing age on the compressive strength of the composite cementitious materials. The microstructure was characterized using hydration heat, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM), and its intrinsic influence mechanism was revealed. The results show that increasing the curing age improves the degree of polymerization reaction and the composite reaches 77~86% of its 7-day compressive strength after 3 days. Except for the composites with 10% and 30% slag content, which reach 33% and 64%, respectively, of their 28-day compressive strength at 7 days, the remaining composites reach more than 95%. This result indicates that the alkali-activated fly ash–slag composite cementitious material has a rapid hydration reaction in the early stage and a slow hydration reaction in the later stage. The amount of slag is the main influencing factor of the compressive strength of alkali-activated cementitious materials. The compressive strength shows a trend of continuous increase when increasing slag content from 10% to 90%, and the maximum compressive strength reaches 80.26 MPa. The increase in the slag content introduces more Ca2+ into the system, which increases the hydration reaction rate, promotes the formation of more hydration products, refines the pore size distribution of the structure, reduces the porosity, and forms a denser microstructure. Therefore, it improves the mechanical properties of the cementitious material. The compressive strength shows a trend of first increasing and then decreasing when the activator concentration increases from 0.20 to 0.40, and the maximum compressive strength is 61.68 MPa (obtained at 0.30). The increase in the activator concentration improves the alkaline environment of the solution, optimizes the level of the hydration reaction, promotes the formation of more hydration products, and makes the microstructure denser. However, an activator concentration that is too large or too small hinders the hydration reaction and affects the strength development of the cementitious material.

Mechanical Properties of Fly Ash–Slag Based Alkali-Activated Materials under the Low-Energy Consummation-Sealed Curing Condition

Preparation of Coal Gasification Coarse Slag-Based Alkaline Activator and Its Activation Mechanism in Alkali-Activated Slag

Effects of Na2CO3/Na2SiO3 Ratio and Curing Temperature on the Structure Formation of Alkali-Activated High-Carbon Biomass Fly Ash Pastes

Influence of alkaline activator solution ratio on the properties of biomass fly ash-based alkali-activated materials

Study of the Mechanical Properties and Microstructure of Alkali-Activated Fly Ash–Slag Composite Cementitious Materials

Effect of curing conditions on the alkali-activated blends: Microstructure, performance and economic assessment

Microstructure and phase characterizations of fly ash cements by alkali activation

Microstructure, strength development mechanism, and CO2 emission analyses of alkali-activated fly ash-slag mortars

Assessment of the performance of alkali-activated slag/fly ash using liquid and solid activators: early-age properties and efflorescence

Effect of fly ash and gypsum on drying shrinkage and mechanical properties of one‐part alkali‐activated slag mortar

Effect of curing regime on the performance and microstructure characteristics of alkali-activated slag-fly ash blended concrete

Effects of Curing Time to Engineering Properties of Alkaline Activated Materials Synthesized from Thu Duc Water Plant Waste Sludge, Fly Ash, and Geopolymer Aggregate

Modification mechanism of flue gas desulfurization gypsum on fly ash and ground granulated blast-furnace slag alkali-activated materials: Promoting green cementitious material

The Effect of Blast Furnace Slag/Fly Ash Ratio on Setting, Strength, and Shrinkage of Alkali-Activated Pastes and Concretes

Effect of Ordinary Portland Cement and Water Glass on the Properties of Alkali Activated Fly Ash Concrete

Design and Microstructural Analysis of the Mixture Proportion of Alkali-Activated Fly Ash-Slag Composite Cementitious Material

Mechanical Properties of High Early Strength Class C Fly Ash-Based Alkali Activated Concrete

A Study on the Influence of Sodium Silicate Concentration and SiO2 : Na2O Ratio on the Properties of Low-Calcium Fly Ash-Based Alkali-Activated Materials Cured at Ambient Condition

Effect of activator on rheological properties of alkali-activated slag-fly ash pastes

Strength and Microstructural Characteristics of Activated Fly Ash–Cement Paste

The Influence of CaO and MgO on the Mechanical Properties of Alkali-Activated Blast Furnace Slag Powder