Abstract:Composites that use fly ash and slag as alkali-activated materials instead of cement can overcome the defects and negative effects of alkali-activated cementitious materials prepared with the use of an alkali-activated material. In this study, fly ash and slag were used as raw materials to prepare alkali-activated composite cementitious materials. Experimental studies were carried out on the effects of the slag content, activator concentration and curing age on the compressive strength of the composite cementitious materials. The microstructure was characterized using hydration heat, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM), and its intrinsic influence mechanism was revealed. The results show that increasing the curing age improves the degree of polymerization reaction and the composite reaches 77~86% of its 7-day compressive strength after 3 days. Except for the composites with 10% and 30% slag content, which reach 33% and 64%, respectively, of their 28-day compressive strength at 7 days, the remaining composites reach more than 95%. This result indicates that the alkali-activated fly ash–slag composite cementitious material has a rapid hydration reaction in the early stage and a slow hydration reaction in the later stage. The amount of slag is the main influencing factor of the compressive strength of alkali-activated cementitious materials. The compressive strength shows a trend of continuous increase when increasing slag content from 10% to 90%, and the maximum compressive strength reaches 80.26 MPa. The increase in the slag content introduces more Ca2+ into the system, which increases the hydration reaction rate, promotes the formation of more hydration products, refines the pore size distribution of the structure, reduces the porosity, and forms a denser microstructure. Therefore, it improves the mechanical properties of the cementitious material. The compressive strength shows a trend of first increasing and then decreasing when the activator concentration increases from 0.20 to 0.40, and the maximum compressive strength is 61.68 MPa (obtained at 0.30). The increase in the activator concentration improves the alkaline environment of the solution, optimizes the level of the hydration reaction, promotes the formation of more hydration products, and makes the microstructure denser. However, an activator concentration that is too large or too small hinders the hydration reaction and affects the strength development of the cementitious material.

Design and Microstructural Analysis of the Mixture Proportion of Alkali-Activated Fly Ash-Slag Composite Cementitious Material

Activation and Toxicity of Slag-fly Ash-fluorgypsum Cementitious Material

Preparation of Coal Gasification Coarse Slag-Based Alkaline Activator and Its Activation Mechanism in Alkali-Activated Slag

Study of the Mechanical Properties and Microstructure of Alkali-Activated Fly Ash–Slag Composite Cementitious Materials

Utilization of Copper–Molybdenum Tailings to Enhance the Compressive Strength of Alkali-Activated Slag-Fly Ash System

Effect of Solid Sodium Silicate on Workability, Hydration and Strength of Alkali-Activated GGBS/Fly Ash Paste

Microstructure, strength development mechanism, and CO2 emission analyses of alkali-activated fly ash-slag mortars

Microstructures and properties of alkali-activated slags with composite activator: Effects of Na2O equivalents

Study on the preparation, performance, and mechanism for solid waste cementitious materials

Study on Optimization of Mixing Ratio and Shrinkage Property of Alkali-Activated Ultrafine Fly Ash-Slag Mortar

Mechanical Property And Structure Of Alkali-Activated Fly Ash And Slag Blends

The Effect of Blast Furnace Slag/Fly Ash Ratio on Setting, Strength, and Shrinkage of Alkali-Activated Pastes and Concretes

Influence of Different Parameters on the Performance of Alkali-Activated Slag/Fly Ash Composite System

Workability, Autogenous Shrinkage and Microstructure of Alkali-Activated Slag/fly Ash Slurries: Effect of Precursor Composition and Sodium Silicate Modulus

Optimization of Alkali-Activated Municipal Slag Composite Performance by Substituting Varying Ratios of Fly Ash for Fine Aggregate

Hydrothermal synthesis and characterization of alkali-activated slag-fly ash-metakaolin cementitious materials

Effect of Fly Ash to Slag Ratio and Na2O Content on Leaching Behaviour of Fly Ash/Slag Based Alkali Activated Materials

Modification mechanism of flue gas desulfurization gypsum on fly ash and ground granulated blast-furnace slag alkali-activated materials: Promoting green cementitious material

The Ratio Optimization and Strength Mechanism of Composite Cementitious Material with Low-Quality Fly Ash

Effect of Alkali Sulfates in Clinker on Hydration and Hardening Properties of Cement Incorporating SCMs

ACTIVATED MECHANISM OF FLY ASH IN PORTLAND CEMENT CONTAINING CALCIUM SULPHOALUMINATE