Abstract:Composites that use fly ash and slag as alkali-activated materials instead of cement can overcome the defects and negative effects of alkali-activated cementitious materials prepared with the use of an alkali-activated material. In this study, fly ash and slag were used as raw materials to prepare alkali-activated composite cementitious materials. Experimental studies were carried out on the effects of the slag content, activator concentration and curing age on the compressive strength of the composite cementitious materials. The microstructure was characterized using hydration heat, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM), and its intrinsic influence mechanism was revealed. The results show that increasing the curing age improves the degree of polymerization reaction and the composite reaches 77~86% of its 7-day compressive strength after 3 days. Except for the composites with 10% and 30% slag content, which reach 33% and 64%, respectively, of their 28-day compressive strength at 7 days, the remaining composites reach more than 95%. This result indicates that the alkali-activated fly ash–slag composite cementitious material has a rapid hydration reaction in the early stage and a slow hydration reaction in the later stage. The amount of slag is the main influencing factor of the compressive strength of alkali-activated cementitious materials. The compressive strength shows a trend of continuous increase when increasing slag content from 10% to 90%, and the maximum compressive strength reaches 80.26 MPa. The increase in the slag content introduces more Ca2+ into the system, which increases the hydration reaction rate, promotes the formation of more hydration products, refines the pore size distribution of the structure, reduces the porosity, and forms a denser microstructure. Therefore, it improves the mechanical properties of the cementitious material. The compressive strength shows a trend of first increasing and then decreasing when the activator concentration increases from 0.20 to 0.40, and the maximum compressive strength is 61.68 MPa (obtained at 0.30). The increase in the activator concentration improves the alkaline environment of the solution, optimizes the level of the hydration reaction, promotes the formation of more hydration products, and makes the microstructure denser. However, an activator concentration that is too large or too small hinders the hydration reaction and affects the strength development of the cementitious material.

Influence of alkaline activator solution ratio on the properties of biomass fly ash-based alkali-activated materials

Effects of Na2CO3/Na2SiO3 Ratio and Curing Temperature on the Structure Formation of Alkali-Activated High-Carbon Biomass Fly Ash Pastes

Mechanical Properties of Fly Ash–Slag Based Alkali-Activated Materials under the Low-Energy Consummation-Sealed Curing Condition

Utilising Phosphogypsum and Biomass Fly Ash By-Products in Alkali-Activated Materials

Assessment of the performance of alkali-activated slag/fly ash using liquid and solid activators: early-age properties and efflorescence

Factors affecting compressive strength and expansion due to alkali-silica reaction of fly ash-based alkaline activated mortar

A Study on the Influence of Sodium Silicate Concentration and SiO2 : Na2O Ratio on the Properties of Low-Calcium Fly Ash-Based Alkali-Activated Materials Cured at Ambient Condition

Fresh and Hardened Properties of Alkali-Activated Fly Ash/slag Binders: Effect of Fly Ash Source, Surface Area, and Additives

Microstructure, strength development mechanism, and CO2 emission analyses of alkali-activated fly ash-slag mortars

Effect of activator on rheological properties of alkali-activated slag-fly ash pastes

Alkali-activated materials partially activated using flue gas residues: An insight into reaction products

The Effect of Blast Furnace Slag/Fly Ash Ratio on Setting, Strength, and Shrinkage of Alkali-Activated Pastes and Concretes

Study of the Mechanical Properties and Microstructure of Alkali-Activated Fly Ash–Slag Composite Cementitious Materials

Improvement of Early Strength of Fly Ash-Slag Based One-Part Alkali Activated Mortar

Effect of borax-modified activator on mechanical properties and drying shrinkage of alkali-activated slag/metakaolin mortar

Preparation of Alkali Activated Cementitious Material by Upgraded Fly Ash from MSW Incineration

Formulation and characterization of cleaner one-part novel fly ash/lime-based alkali-activated material

Strength and Microstructural Characteristics of Activated Fly Ash–Cement Paste

Alkali-activated fly ash cured with pulsed microwave and thermal oven: A comparison of reaction products, microstructure and compressive strength

Optimization on the Piezoresistivity of Alkali-Activated Fly Ash/slag Mortar by Using Conductive Aggregates and Carbon Fibers

Fast setting and high early strength alkali-activated fly ash synthetized with pre-polymerized suspension combined with ultrafine fly ash at ambient temperature