Abstract:LaMgAl11O19 (LMA) with magnetoplumbite structure has been identified as a potential candidate for the next generation of thermal barrier coatings (TBCs). However, the as-sprayed LMA coating presents a large amount of amorphous phase originating from the rapid quenching from the molten droplets, which may compromise the reliability of coating during high-temperature service. A logical approach to improve LMA TBC life, therefore, is to enhance its crystallinity. In the present study, three LMA powders with different particle size distributions (fine, medium and coarse feedstocks) were utilized to deposit TBCs to investigate whether the thermal durability of LMA can be improved by increasing particle size. It was based on a hypothesis that large particle size can decrease the melting degree of in-flight particles and thus result in high crystallinity of as-sprayed LMA coating, making less recrystallization stress to enhance the thermal shock resistance of LMA coating. Results show that prolonged thermal cycling durability can indeed be achieved by increasing particle size. However, excessive particle size could lead to higher porosity derived from unmelted particles, which function as the weak regions for the coating system, thereby damaging the structural integrity and adhesive strength between the topcoat and bond coat. This could cause microcrack linking when the accumulated thermal stress exceeds its fracture toughness under consecutive heating-cooling cycles despite its higher crystallinity. Concerning the coating fabricated by medium powder, it achieves the optimal balance of crystallinity and structure integrity, resulting in the longest thermal cycling lifetime. The results provide guidance for the development and design of high thermal durability LMA TBCs. When optimizing the recrystallization stress within the coating, attention should be paid to improving its bonding strength simultaneously.

Microstructures, thermophysical properties and thermal cyclic behaviors of Nd2O3 and Sc2O3 co-doped LaMgAl11O19 thermal barrier coating deposited by plasma spraying

The Microstructure of Al2O3/TiO2-NiCrBSi Graded Thermal Barrier Coatings Produced by Flame Spraying

Improvement on thermophysical and mechanincal properties of LaMgAl11O19 magnetoplumbite by Nd2O3 and Sc2O3 co-doping

Influence of Amorphous Phase in LaMgAl11O19 on Properties of LaMgAl11O19/YSZ Thermal Barrier Coatings

Microstructure, thermal shock resistance and thermal emissivity of plasma sprayed LaMAl11O19 (M = Mg, Fe) coatings for metallic thermal protection systems

Prolonged thermal durability of plasma-sprayed lanthanum hexaluminate thermal barrier coating by optimizing crystallinity

Influence of Ln3+ and B3+ Ions Co‐Substitution on Thermophysical Properties of LnMB11O19‐type Magnetoplumbite LaMgAl11O19 for Advanced Thermal Barrier Coatings

Infrared radiation and thermal cyclic performance of a high-entropy rare-earth hexaaluminate coating prepared by atmospheric plasma spraying

NdAlO3-Nd2Zr2O7 composite with eutectic composition for advanced nanostructured thermal insulation coatings

High-temperature degradation of the in-situ laser-glazed plasma sprayed LaMgAl11O19 thermal barrier coating exposed to Ca-Mg-Al-silicate deposits

Low Thermal Conductivity Sr 2+ , Zn 2+ and Ti 4+ Ions Co-Doped LaMgAl 11 O 19 for Potential Thermal Barrier Coating Applications

Ca-Mn co-doping LaCrO3 coating with high emissivity and good mechanical property for enhancing high-temperature radiant heat dissipation

Isothermal Oxidation and Thermal Shock Resistance of Thick and Porous LaMgAl11O19 Abradable Topcoat

An investigation on the microstructure and oxidation behavior of laser remelted air plasma sprayed thermal barrier coatings

Oxidation behavior and structural damage mechanism of LaMgAl 11 O 19 dual-ceramic thermal barrier coating with varying thickness of Al plating layer

Thermo-physical Properties of Rare-Earth Hexaaluminates LnMgAl11O19 (ln: La, Pr, Nd, Sm, Eu and Gd) Magnetoplumbite for Advanced Thermal Barrier Coatings

Synthesis and Characterization of LaMgAl11O19 As Thermal Barrier Coatings Material

Dependence of Crystal Structure on Mechanical and Thermophysical Properties of Magnetoplumbite‐type LnMgAl11O19 Ceramics with Substitution of Ln3+ Ions

Influence of Original Powders on the Microstructure and Properties of Thermal Barrier Coatings Deposited by Supersonic Atmospheric Plasma Spraying, Part Ii: Properties

Composition Effects of La2Ce2O7 Thermal Barrier Coatings Against Calcium-Magnesium-Aluminum-Silicate (CMAS) at 1250°C

Composition optimization, high-temperature stability, and thermal cycling performance of Sc-doped Gd2Zr2O7 thermal barrier coatings: Theoretical and experimental studies