Abstract:In the current study, the low carbon Ni-based superalloy Inconel-738 (IN-738LC) was used as the substrate and a metallic bond coat (NiCrAlY) was deposited on the substrate by air plasma spray (APS) method. Subsequently, the layer was coated by a ceramic interlayer Yttria-stabilized zirconia (YSZ) by APS. Finally, as the last ceramic layer, a hybrid ceramic top layer containing mullite and YSZ was plasma deposited on the YSZ interlayer in various compositions such as: 25 wt% mullite/75 wt% YSZ, 50 wt% mullite/50 wt% YSZ, 75 wt% mullite/25 wt% YSZ, and 100 wt% mullite. In order to investigate the oxidation resistance of the produced TBCs, they were heated at 1000 °C for 50 and 100 h. The results showed that the presence of mullite phase is advantageous to hybrid coatings, so that in the 50 wt% mullite/50 wt% YSZ hybrid coating, the percentage of destructive spinel oxides forming the thermally grown oxide (TGO) layer reduced compared to the 25 wt% mullite/75 wt% YSZ coating. Moreover, aluminum oxide is the dominant oxide in the 50 wt% mullite/50 wt% YSZ hybrid coating. However, the further increase in the mullite percentage had no noticeable effect on the reduction of spinel oxides. In addition, the presence of mullite alongside YSZ led to an increase in the hardness of the 25 wt% mullite/75 wt% YSZ hybrid coating (845 HV) compared to the conventional coating including a YSZ layer (680 HV) or a mullite layer (655 HV). The X-ray diffraction (XRD) analysis revealed that the presence of mullite beside YSZ in the coating increases the stability of the coating after oxidation test so that, in the XRD pattern, monoclinic phase was not detected in the hybrid coatings. In general, 50 wt% mullite/50 wt% YSZ hybrid coating provided the best results compared to other coatings. Moreover, with increasing thickness of the hybrid ceramic layer containing 50 wt% mullite to 350 μm, the thickness of the TGO layer decreased to approximately 7 μm. Additionally, it was shown that due to the decrease of chromium and nickel elements in the TGO layer, the level of the spinel oxides in the thick coatings decreases. This led to an increase in the stability of the TGO layer and an extension of the thermal system's lifespan.

Superposed structure of double-ceramic layer based on YSZ/LaMgAl11O19 thermal barrier coating

Novel thermal barrier coatings based on Mg2SiO4/8YSZ double-ceramic-layer systems deposited by APS

Thermal cycling and steam corrosion behavior of Yb3Al5O12‐based multilayered environmental barrier coatings for SiCf/SiC

Thermal shock life and failure behaviors of La2Zr2O7/YSZ, La2Ce2O7/YSZ and Gd2Zr2O7/YSZ DCL TBCs by EB-PVD

LC/8YSZ TBCs Thermal Cycling Life and Failure Mechanism under Extreme Temperature Gradients

LaYbZrO thermal barrier coatings by EB-PVD: Microstructure, thermal shock life and failure behaviors

Thermal Cycling Behavior and Failure Mechanism of LaTi2Al9O19/YSZ Thermal Barrier Coatings Exposed to Gas Flame

Properties evaluation and failure behaviour of plasma sprayed Y4Hf3O12 for thermal barrier coating applications

Sintering governing the cracking behaviors of different La2Zr2O7/YSZ ceramic layer combination TBCs at 1150 °C

Superior toughness of thermal barrier coating caused by co-doping of trivalent and pentavalent oxides

Mechanical Properties of LaTi2Al9O19 and Thermal Cycling Behaviors of Plasma-Sprayed LaTi2Al9O19/YSZ Thermal Barrier Coatings

Thermal cycling performance of GYbZ/YSZ thermal barrier coatings with different microstructures based on finite element simulation

Investigation of Thermal Shock Behavior of Multilayer Thermal Barrier Coatings with Superior Erosion Resistance Prepared by Atmospheric Plasma Spraying

Oxidation behavior and interface evolution of tri-layer Si/Yb2SiO5/LaMgAl11O19 thermal and environmental barrier coatings under isothermal heat treatment at 1300 °C

Multilayer GZ/YSZ Thermal Barrier Coating from Suspension and Solution Precursor Plasma Spray

Thermal shock performance and failure behavior of Zr6Ta2O17-8YSZ double-ceramic-layer thermal barrier coatings prepared by atmospheric plasma spraying

Thermal cycle and water oxygen performance of multi-layered Y3Al5O12/Yb2SiO5/Yb2Si2O7 thermal/environmental barrier coatings

Thermophysical properties and cyclic lifetime of plasma sprayed SrAl 12 O 19 for thermal barrier coating applications

Mullite/YSZ hybrid thermal barrier coatings plasma sprayed on IN-738LC: Microstructure, phase analysis and oxidation resistance

High-entropy thermal barrier coating of rare-earth zirconate: A case study on (La0.2Nd0.2Sm0.2Eu0.2Gd0.2)2Zr2O7 prepared by atmospheric plasma spraying

Thermal cycling of EB-PVD TBCs based on YSZ ceramic coat and diffusion aluminide bond coat