Abstract:In this paper, we analyze the autothermal reforming (ATR) of methane through Gibbs energy minimization and entropy maximization methods to analyze isothermic and adiabatic systems, respectively. The software GAMS® 23.9 and the CONOPT3 solver were used to conduct the simulations and thermodynamic analyses in order to determine the equilibrium compositions and equilibrium temperatures of this system. Simulations were performed covering different pressures in the range of 1 to 10 atm, temperatures between 873 and 1073 K, steam/methane ratio was varied in the range of 1.0/1.0 and 2.0/1.0 and oxygen/methane ratios in the feed stream, in the range of 0.5/1.0 to 2.0/1.0. The effect of using pure oxygen or air as oxidizer agent to perform the reaction was also studied. The simulations were carried out in order to maintain the same molar proportions of oxygen as in the simulated cases considering pure oxygen in the reactor feed. The results showed that the formation of hydrogen and synthesis gas increased with temperature, average composition of 71.9% and 56.0% using air and O2, respectively. These results are observed at low molar oxygen ratios (O2/CH4 = 0.5) in the feed. Higher pressures reduced the production of hydrogen and synthesis gas produced during ATR of methane. In general, reductions on the order of 19.7% using O2 and 14.0% using air were observed. It was also verified that the process has autothermicity in all conditions tested and the use of air in relation to pure oxygen favored the compounds of interest, mainly in conditions of higher pressure (10 atm). The mean reductions with increasing temperature in the percentage increase of H2 and syngas using air under 1.5 and 10 atm, at the different O2/CH4 ratios, were 5.3%, 13.8% and 16.5%, respectively. In the same order, these values with the increase of oxygen were 3.6%, 6.4% and 9.1%. The better conditions for the reaction include high temperatures, low pressures and low O2/CH4 ratios, a region in which there is no swelling in terms of the oxygen source used. In addition, with the introduction of air, the final temperature of the system was reduced by 5%, which can help to reduce the negative impacts of high temperatures in reactors during ATR reactions.

Two-section reactor model for autothermal reforming of methane to synthesis gas

Modeling and Simulation of Commercial Catalytic Reformers

Characterization of CH4-CO2-O2 Diffusion Flames Near Autothermal Reforming Condition

The Effects of CO2/CH4 Ratio on Soot Formation for Autothermal Reforming of Methane at Elevated Pressure

Steam reforming of methane over nickel catalyst using a one-dimensional model

STEAM REFORMING OF METHANE IN CATALYTIC MICROREACTORS FOR HYDROGEN PRODUCTION

An Annular Reactor for Direct Methane Autothermal Reforming

Modeling and Design of a Multi-Tubular Packed-Bed Reactor for Methanol Steam Reforming over a Cu/ZnO/Al2O3 Catalyst

Modelling Of One-Step Methanation Process Combining Soecs And Fischer-Tropsch-Like Reactor

Multi-dimensional modeling of non-catalytic partial oxidation of natural gas in a high pressure reformer

Modeling and Performance Analysis of Gas Auto-Thermal Reformer

Numerical Simulation of Natural Gas Non-Catalytic Partial Oxidation Reformer

DEM-based model for steam methane reforming

Cold modeling of a direct coupling autothermal methane reforming reactor

On the Modeling of Steam Methane Reforming

Autothermal Reforming of Methane: A Thermodynamic Study on the Use of Air and Pure Oxygen as Oxidizing Agents in Isothermal and Adiabatic Systems

One Dimensional Reactor Modeling for Methanol Steam Reforming to Hydrogen

Steam methane reforming driven by the Joule heating

Characteristic Study of Micro-channel Auto-thermal Reforming of Methane with Ni/Rh Catalysts

Hybrid Modeling of Integrated Microchannel Methane Reformer for Miniaturized GTL Application Using an Effectiveness Factor Submodel Based on Complex Surface Chemistry

Simulation Analysis of Gas-Solid Two-Phase Flow and Reaction in a Novel Catalytic Cracking Reactor