Steam Reforming of Methane in Metal-foam Filled Reactor
Y. P. Du,C. Y. Zhao,Y. Zhu
2014-01-01
Abstract:As a unique porous media, open-cell metal foams wit h high porosity, high specific surface area and strong hea t transfer capability is highly potential to be used to increa s the conversion rate of methane to hydrogen. Steam refor ming of methane in metal-foam filled reactor was studied in this paper. An innovative chemistry model was developed in whic h the reactive rateJ and volume expanding rate δ were associated with partial pressure, density and concentration in the c mical reactions. While reactive heat addition and mass di ffusion were considered as inner thermal sources in the temperat ur equation for fluid. The methane conversion rate and distribu ion of fluid temperature were investigated. It was found that me al foams improved the conversion by its higher thermal condu ctivity of solid matrix, bigger cell size and smaller cell lig ament diameter. It was demonstrated that higher average temperature long the flow direction is caused by metal foams. The peak s ectionaverage temperature of fluid appeared close to the entrance of the reactor and increased simultaneously with the incre asing of conversion of methane to hydrogen. It is explained that moving of the chemical equilibrium of steam reforming was due to better endothermic reaction and longer contacting time of amount of substance with metal-foam filled in the reactor. Introduction Steam methane reforming (SMR) is widely used for pro ducing hydrogen, through which about 50% of hydrogen deman d in chemical manufacturing and petroleum refining is sa tisfied [1]. However, heat and mass diffusion in the process of steam methane reforming was relatively limited [2]. Opencell metal foams could be used for addressing the above limita tions, since the complex 3-D matrix of open-cell metal foams cou ld thin both velocity and heat boundary layers of the flowing fl uid [3-4]. By sintering open-cell metal foams in a chemical react or, the conversion rate of hydrogen by SMR is largely improv ed. The chemical kinetics for steam reforming was found i [5-9]. Conventional wisdom showed that steam methane reform ing included more than two reactions, through which bot h CO and CO2 were formed during the hydrogen production [5]. To investigate the further kinetics, Lin et al [6] reg arded the SMR as combination of steam reforming and water gas shift reactions. Craciun et al [7] argued that SMR occurred through a bifunctional mechanism consisting of reactions of oxy gen from ceria and the dissociated methane on the previous m etal. While Abashar [8-9] established mathematical model of flu idized bed membrane reactors for SMR based on the four-step rea ction mechanism. All of the above researchers considered SMR as multi-step reactions, leading to complexity of pred icting the conversion rate. However, due to the use of various catalysts, the reactive processes were largely shortened. As a res ult, SMR can be regarded as one-step reactions. Nevertheless, pe rformance of SMR is highly dependent on the catalyst used in the reactions, owing to its effect on the endothermic characterist ics of the reactions. By using catalysts, the reactive temperat ure was reduced [10] and the heat transfer and dynamic resp onse during the reactions were improved [11]. Thermal performance of SMR in porous-media supported reactor was extensively studied [1, 12-15]. Yu et al [1] an alysed the performance of porous ceramic membrane for hydrogen production by SMR. Raviraj et al [12] studied the con version of methane to hydrogen in a porous media reactor. Leve nt [13] investigated the distribution of concentration and temperature in porous catalyst. Luna [14] reported the performance of the SMR in the range of 773-873K, using alumina-titania as the catalyst. Yang et al [15] investigated the influence of tempe rature, ratio of H2O and CH4, porosity of porous media on methane steam reforming in planar porous support of solid oxide f uel cell. However, most of the studies were based on one-dime nsional heat transfer model, and presented vague informatio n about the influence of reactive heat and mass diffusion in SM R. In this study, a two-dimensional model was establis hed for the SMR in a metal-foam supported reactor. Special atten tion was paid on processing the reactive heat and variable d ensity of reactants. Parametric study was carried out for exp loring the achieving optimal conversion rate of SMR in metal-fo am filled reactor. Theoretical Models Chemical Kinetics Model Under certain thermal conditions, steam reforming o f methane can be described as a reversible chemical reaction as shown in equation (1) (Abashar [3, 4]): mol kJ H CO O H CH / 206 3 2 2 4 + + = + (1) The mixture of the reactants was regarded as an ide ally flowing system under the hypothesis of continuous reactions . No lag or deposit was proposed in metal-foam filled reactor. As a result, the reactive rate was formulated in equation (2) by A ashar [4]: 2 4 2 2 3 2 2.5 . J . ( . ) / , /( . ) H CO CH H O H P P k P P DEN mol kg s K P ρ = − (2) In the formula, 4 2 2 , , , , CH H O CO H P P P P ρ are density of the reactive fluid mixture, partial pressure of 4 CH , 2 H O , CO , 2 H , respectively; k represents the rate constant; K is the equilibrium constant of the above reaction. Detailed calculations of parame ters were listed in Abashar [4]. However, partial pressure, t emperature and density of the reactants were not mentioned in the li erature. The physical properties of the mixed reactants coul d be obtained in terms of ideal gas state equations and Dalton’s law of partial pressure. For steam reforming of methane in metal f o ms, the volume expanding was described in equation (3): j j j i i i B A ⋅ = ⋅ ∑ ∑ η φ (3) In which i A , j B are reactants and products while i φ , j η denote volume coefficients for the above reactants and pro ucts. Volume expanding rate δ demonstrated the variation of the total volume, resulting in changing pressure and density during t he reaction, which was defined as in equation (4): ) ( 1 ∑ ∑ − ⋅ = i i j j i φ η φ δ (4) For steam reforming in Eq. (1), volume expanding ra te was calculated as 2 δ = . Ideal gas equation and Dalton's law of partial pressures were formulated as equation (5) and (6):