Abstract:Introduction: The cervical spine, pivotal for mobility and overall body function, can be affected by cervical spondylosis, a major contributor to neural disorders. Prevalent in both general and military populations, especially among pilots, cervical spondylosis induces pain and limits spinal capabilities. Anterior Cervical Discectomy and Fusion (ACDF) surgery, proposed by Cloward in the 1950s, is a promising solution for restoring natural cervical curvature. The study objective was to investigate the impacts of ACDF implant design on postsurgical cervical biomechanics and neurorehabilitation outcomes by utilizing a biofield head-neck finite element (FE) platform that can facilitate scenario-specific perturbations of neck muscle activations. This study addresses the critical need to enhance computational models, specifically FE modeling, for ACDF implant design. Materials and methods: We utilized a validated head-neck FE model to investigate spine-implant biomechanical interactions. An S-shaped dynamic cage incorporating titanium (Ti) and polyetheretherketone (PEEK) materials was modeled at the C4/C5 level. The loading conditions were carefully designed to mimic helmet-to-helmet impact in American football, providing a realistic and challenging scenario. The analysis included intervertebral joint motion, disk pressure, and implant von Mises stress. Results: The PEEK implant demonstrated an increased motion in flexion and lateral bending at the contiguous spinal (C4/C5) level. In flexion, the Ti implant showed a modest 5% difference under 0% activation conditions, while PEEK exhibited a more substantial 14% difference. In bending, PEEK showed a 24% difference under 0% activation conditions, contrasting with Ti's 17%. The inclusion of the head resulted in an average increase of 18% in neck angle and 14% in C4/C5 angle. Disk pressure was influenced by implant material, muscle activation level, and the presence of the head. Polyetheretherketone exhibited lower stress values at all intervertebral disc levels, with a significant effect at the C6/C7 levels. Muscle activation level significantly influenced disk stress at all levels, with higher activation yielding higher stress. Titanium implant consistently showed higher disk stress values than PEEK, with an orders-of-magnitude difference in von Mises stress. Excluding the head significantly affected disk and implant stress, emphasizing its importance in accurate implant performance simulation. Conclusions: This study emphasized the use of a biofidelic head-neck model to assess ACDF implant designs. Our results indicated that including neck muscles and head structures improves biomechanical outcome measures. Furthermore, unlike Ti implants, our findings showed that PEEK implants maintain neck motion at the affected level and reduce disk stresses. Practitioners can use this information to enhance postsurgery outcomes and reduce the likelihood of secondary surgeries. Therefore, this study makes an important contribution to computational biomechanics and implant design domains by advancing computational modeling and theoretical knowledge on ACDF-spine interaction dynamics.

Development, calibration and validation of impact-specific cervical spine models: A novel approach using hybrid multibody and finite-element methods

Development and Validation of a Finite Element Model of Human Cervical Spine Based on the Head-Neck Drop Test

Musculoskeletal modelling of the human cervical spine for the investigation of injury mechanisms during axial impacts

Development of a Finite Element Model of the Cervical Spine and Validation of a Functional Spinal Unit

Simulative investigation of the required level of geometrical individualization of the lumbar spines to predict fractures

Subject-Specific Geometry of FE Lumbar Spine Models for the Replication of Fracture Locations Using Dynamic Drop Tests

Calibration and validation of a novel hybrid model of the lumbosacral spine in ArtiSynth–The passive structures

[Building an effective nonlinear three-dimensional finite-element model of human thoracolumbar spine]

Development of a biofidelic computational model of human pelvis for predicting biomechanical responses and pelvic fractures

A cervical spine model to predict injury scenarios and clinical instability

Development and validation of lumbar spine finite element model

Development and Validation of a 10-Year-old Child Ligamentous Cervical Spine Finite Element Model

Implant Design and Cervical Spinal Biomechanics and Neurorehabilitation: A Finite Element Investigation

Development and validation of a human neck FE model for dynamic response during impact condition]

Estimating Facet Joint Apposition with Specimen-Specific Computer Models of Subaxial Cervical Spine Kinematics

Development And Tensile Investigation Of A 3-Year-Old Cervical Spine Finite Element Model

Finite Element Modeling and Static/dynamic Validation of Thoracolumbar-Pelvic Segment.

Smoothed particle hydrodynamics implementation to enhance vertebral fracture finite element model in a cervical spine segment under compression

Recent Advances in Coupled MBS and FEM Models of the Spine-A Review

Load-Sharing and Kinematics of the Human Cervical Spine Under Multi-Axial Transverse Shear Loading: Combined Experimental and Computational Investigation

Three-dimensional finite element modeling of whole lumbar spine and its biomechanical analysis