Abstract:In this dissertation, the relationships between structure-mechanical properties-deformation mechanisms in face-centered cubic (FCC) and body-centered cubic (BCC) metallic nanowires have been studied using in situ TEM nanomechanical testing. It is well known that smaller is stronger and the widely-observed size effect is believed to arise from dislocation interactions inside nanocrystals. However, the interaction mechanisms in small-volume nanocrystals remain unexplored. Here, it was found that surface-nucleated dislocations can strongly interact inside the confined volume of Au nanowires, which led to a new type of dislocation-originated stacking fault tetrahedra (SFT), at variance to the widely-believed vacancy-originated SFT. The atomic-scale processes of nucleation, migration and annihilation of dislocation-originated SFT were revealed, shedding new light onto the strain hardening and size effect in small-volume materials. Although nanoscale twinning is an effective mean to enhance the strength of metals, twin-size effect on the deformation and failure of nanotwinned metals remains largely unexplored, especially at the minimum twin size. Here, a new type of size effect in nanotwinned Au nanowires is presented. As twin size reaches the angstrom-scale, Au nanowires exhibit a remarkable ductile-to-brittle transition that is governed by the heterogeneous-to-homogeneous dislocation nucleation transition. Quantitative measurements show that approaching such a nanotwin size limit gives rise to the ultra-high strength in Au nanowires, close to the ideal strength limit of perfect Au. Twinning is a fundamental deformation mode that competes against dislocation slip in crystals. At the nanoscale, higher stresses are required for plastic deformation than that in bulk, which favors twinning over dislocation slip. Indeed, deformation twinning has been well-documented in FCC nanocrystals. However, it remains unexplored in BCC nanostructures. Here, it shows that twinning is the dominant deformation mode in BCC-tungsten nanocrystals. A competition between twinning and dislocation slip occurs when changing the loading orientations, attributed to the defect growth controlled plasticity in BCC nanocrystals. Several important commonalities and differences in FCC and BCC nanocrystals deforming at nanoscale are further proposed. The results from this dissertation advance fundamental understanding of plastic deformation in a broad class of metals and alloys, and are of technological importance for degradation control and future design of ultra-strength nanomaterials.

Mechanical Behavior of Nanotwinned Cu–Ag Alloys with Solute Atomic Gradient Analysis Under the Influence of Twinning Spacing

Modeling Grain Size Dependent Optimal Twin Spacing for Achieving Ultimate High Strength and Related High Ductility in Nanotwinned Metals

Two softening stages in nanotwinned Cu

Tuning the Strength-Ductility Synergy of Nanograined Cu Through Nanotwin Volume Fraction

Size-Dependent Dislocation-Twin Interactions

In Situ TEM Study on the Nanomechanical Behaviors of Metallic Nanowires

Atomistic and Theoretical Insights on Nanoprecipitates-Controlled Strengthening Behavior for Optimum Mechanical Performance in Nanotwinned NiCoCr Alloys

Discrete Twinning Dynamics and Size-Dependent Dislocation-to Twin Transition in Body-Centred Cubic Tungsten

The Direct and Indirect Effects of Nanotwin Volume Fraction on the Strength and Ductility of Coarse-Grained Metals

Tensile Failure Modes in Nanograined Metals with Nanotwinned Regions

Simulation Study on the Mechanical Behavior of Copper–Silver Alloy with Twinning-Induced Gradient Segregation

Solute-enhanced twin boundary migration in CuAg alloy

Effect of twin spacing on the mechanical behavior and deformation mechanism of nanotwinned Al

A Constitutive Description of the Yield Strength and Strain Hardening Behaviors of Nano-Twinned Metals

Indentation-induced plastic behavior of nanotwinned CuNi alloy: an atomic simulation

Anisotropic Mechanical Properties and Deformation Mechanisms of Nanotwinned Ni and Ni Alloys With Extremely Fine Twin Boundary Spacings

Molecular Dynamics Simulation of Microstructure Evolution During the Fracture Process of Nano-Twinned Ag

Influences of grain size and twin boundary on the tensile properties of nanocrystalline face-centered cubic Cu50Ni50 alloy

Effect of Loading Method, Temperature, and Twin Defects on the Mechanical Behavior of Nanocrystalline Ni with Gradient Spacing Twin Structure

Study on the factors influencing the mechanical properties of bimodal nanotwinned Cu-Ag alloys

Twin-boundary-spacing-dependent strength in gradient nano-grained copper