Abstract:In this study, a novel Ge-Sn based perovskite solar cell (PSC) with the structure FTO/WS2/ FA0.75MA0.25Sn0.95Ge0.05I3/MoO3/Ag has been designed and thoroughly analyzed employing SCAPS-1D. Drawing attention from the work of Ito et al., where a similar perovskite-based PSC displayed a poor performance of ~ 4.48 % PCE, in which a large conduction band offset (CBO) acts as a critical factor contributing to interfacial recombination and device deterioration. To address this issue, we presented WS2 as an electron transport layer (ETL) along with MoO3 as a hole transport layer (HTL), both possessing compatible CBO and valence band offset (VBO) with perovskite material. Through systematic simulations and optimizations, remarkable improvements in the PSC's performance have been acquired, getting a power conversion efficiency (PCE) of 18.97%. The optimized structure involved a 50 nm MoO3 HTL, 350 nm FA0.75MA0.25Sn0.95Ge0.05I3 light-harvesting layer (LHL), and a 50 nm WS2 ETL. Bulk defect densities for the LHL and ETL were optimized to 1×1015 cm-3 and 1×1018 cm-3, respectively, significantly superior values than that of reported value in the literature. Particularly, the tolerable defect density of ETL has increased 1000 times than published literature. The interfacial tolerable trap density for MoO3/perovskite increased from 1×1014 cm-2 to 1×1016 cm-2. The study also explored the impact of defects on quantum efficiency, revealing a severe negative influence beyond a perovskite bulk defect density of 1×1017 cm-3. Light intensity analysis demonstrated a correlation between incident light reduction and device performance decay. Capacitance–Voltage (C-V) and Mott-Schottky (M-S) have been analyzed during the study. Finally, the total recombination of the optimized device concerning thickness has been analyzed along with the dark J-V characteristics. The comprehensive insights gained from this work are anticipated to accelerate the fabrication of mixed Ge-Sn based PSCs with improved efficiency, paving the way for commercialization in the photovoltaic industry.

Numerical analysis of ultra-thin MASnI3 based perovskite solar cell by SCAPS-1D

Utilizing Density Functional Theory and SCAPS Simulations for Modeling High‐Performance MASnI3‐Based Perovskite Solar Cells

Investigating the Performance of FASnI3‐Based Perovskite Solar Cells with Various Electron and Hole Transport Layers: Machine Learning Approach and SCAPS‐1D Analysis

Numerical investigation of structural optimization and defect suppression for high-performance perovskite solar cells via SCAPS-1D

Study and Optimization of a New Perovskite Solar Cell Structure Based on the Two Absorber Materials Cs2TiBr6 and MASnBr3 Using SCAPS 1D

Numerical simulation and optimization of CsPbI3-based perovskite solar cell to enhance the power conversion efficiency

Current Status of Pb-free PSCs and Infer the Highest Achievable PCE Via Numerical Modeling, and Optimization of Novel Structure FAMASnGeI3 Based PSCs

Numerical simulation and performance optimization of a lead-free inorganic perovskite solar cell using SCAPS-1D

Design and simulation of CsPb.625Zn.375IBr2-based perovskite solar cells with different charge transport layers for efficiency enhancement

Numerical analysis of high performance perovskite solar cells with stacked ETLs/C60 using SCAPS-1D device simulator

Performance optimization of eco-friendly CH3NH3SnI3based perovskite solar cell employing CH3NH3SnBr3as hole transport layer by SCAPS-1D device simulator

Improving the perovskite solar cell by insertion of methyl ammonium tin oxide and cesium tin chloride as absorber layers: scaps 1d study based on experimental studies

Numerical Investigation of CuSbS2Thin Film Solar Cell using SCAPS-1D: Enhancement of Efficiency on Experimental Films by Defect Studies

Effect of various electron and hole transport layers on the performance of CsPbI3-based perovskite solar cells: A numerical investigation in DFT, SCAPS-1D, and wxAMPS frameworks

Evaluating the influence of novel charge transport materials on the photovoltaic properties of MASnI3 solar cells through SCAPS-1D modelling

Computational Study of Ternary Devices: Stable, Low-Cost, and Efficient Planar Perovskite Solar Cells

Simulation in SCAPS-1D and optimization of a perovskite solar cell

Revealing the High-Performance of a Novel Ge-Sn-Based Perovskite Solar Cell by Employing SCAPS-1D

Enhanced efficiency of bifacial perovskite solar cells using computational study

Modeling and numerical simulation of high efficiency perovskite solar cell with three active layers

Numerical Simulation of Highly Efficient Cs2TiI6 based Pb Free Perovskites Solar Cell with the Help of Optimized ETL and HTL Using SCAPS-1D Software