Abstract:In this study, a novel perovskite solar cell (PSC) architecture is presented that utilizes an HTL-free configuration with formamide tin iodide (FASnI3) as the active layer and fullerene (C60) as the electron transport layer (ETL), which represents a pioneering approach within the field. The elimination of hole transport layers (HTLs) reduces complexity and cost in PSC heterojunction structures, resulting in a simplified and more cost-effective PSC structure. In this context, an HTL-free tin HC(NH2)2SnI3-based PSC was simulated using the solar cell capacitance simulator (SCAPS) within a one-dimensional framework. Through this approach, the device performance of this novel HTL-free FASnI3-based PSC structure was engineered and evaluated. Key performance parameters, including the open-circuit voltage (Voc), short-circuit current density (Jsc), fill factor (FF), power conversion efficiency (PCE), I-V characteristics, and quantum efficiency (QE), were systematically assessed through the modulation of physical parameters across various layers of the device. A preliminary analysis indicated that the HTL-free configuration exhibited improved I-V characteristics, with a PCE increase of 1.93% over the HTL configuration due to improved electron and hole extraction characteristics, reduced current leakage at the back contact, and reduced trap-induced interfacial recombination. An additional boost to the device's key performance parameters has been achieved through the further optimization of several physical parameters, such as active layer thickness, bulk and interface defects, ETL thickness, carrier concentration, and back-contact materials. For instance, increasing the thickness of the active layer PSC up to 1500 nm revealed enhanced PV performance parameters; however, further increases in thickness have resulted in performance saturation due to an increased rate of hole-electron recombination. Moreover, a comprehensive correlation study has been conducted to determine the optimum thickness and donor doping level for the C60-ETL layer in the range of 10-200 nm and 1012-1019 cm-3, respectively. Optimum device performance was observed at an ETL-C60 ultra-thin thickness of 10 nm and a carrier concentration of 1019 cm-3. To maintain improved PCEs, bulk and interface defects must be less than 1016 cm-3 and 1015 cm-3, respectively. Additional device performance improvement was achieved with a back-contact work function of 5 eV. The optimized HTL-free FASnI3 structure demonstrated exceptional photovoltaic performance with a PCE of 19.63%, Voc of 0.87 V, Jsc of 27.86 mA/cm2, and FF of 81%. These findings highlight the potential for highly efficient photovoltaic (PV) technology solutions based on lead-free perovskite solar cell (PSC) structures that contribute to environmental remediation and cost-effectiveness.

Investigating the Performance of FASnI3‐Based Perovskite Solar Cells with Various Electron and Hole Transport Layers: Machine Learning Approach and SCAPS‐1D Analysis

DFT and SCAPS-1D calculations of FASnI3-based perovskite solar cell using ZnO as an electron transport layer

Advanced Optoelectronic Modeling and Optimization of HTL-Free FASnI3/C60 Perovskite Solar Cell Architecture for Superior Performance

Numerical Simulation and Optimization of Highly Stable and Efficient Lead-Free Perovskite FA1−xCsxSnI3-Based Solar Cells Using SCAPS

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Utilizing Density Functional Theory and SCAPS Simulations for Modeling High‐Performance MASnI3‐Based Perovskite Solar Cells

Numerical analysis of ultra-thin MASnI3 based perovskite solar cell by SCAPS-1D

Low-cost, stable all-inorganic charge transporting layer based FAPI perovskite solar cells achieving ≈ 26% efficiency using SCAPS-1D

SCAPS Empowered Machine Learning Modelling of Perovskite Solar Cells: Predictive Design of Active Layer and Hole Transport Materials

Selection of a compatible electron transport layer and hole transport layer for the mixed perovskite FA0.85Cs0.15Pb (I0.85Br0.15)3, towards achieving novel structure and high-efficiency perovskite solar cells: a detailed numerical study by SCAPS-1D

Performance optimization of eco-friendly CH3NH3SnI3based perovskite solar cell employing CH3NH3SnBr3as hole transport layer by SCAPS-1D device simulator

Utilizing machine learning to enhance performance of thin-film solar cells based on Sb2(S x Se1- x )3: investigating the influence of material properties

SCAPS-1D Simulation for Device Optimization to Improve Efficiency in Lead-Free CsSnI3 Perovskite Solar Cells

Using Cu2O/ZnO as Two-Dimensional Hole/Electron Transport Nanolayers in Unleaded FASnI3 Perovskite Solar Cells

Improving the perovskite solar cell by insertion of methyl ammonium tin oxide and cesium tin chloride as absorber layers: scaps 1d study based on experimental studies

Device modeling of high performance and eco-friendly FAMASnI 3 based perovskite solar cell

Achieving beyond 30% efficiency for hole-transport-layer-free CsSnI3 perovskite solar cell: A comprehensive simulation study

Design of Homojunction Perovskite Solar-Cell Devices Without Hole-Transport Layer

Comprehensive investigation of material properties and operational parameters for enhancing performance and stability of FASnI3-based perovskite solar cells

An augmented lead-free Perovskite solar cell based on FASnI3 using V2O5 as HTL

Design and simulation of CsPb.625Zn.375IBr2-based perovskite solar cells with different charge transport layers for efficiency enhancement