Abstract:In this study, a novel perovskite solar cell (PSC) architecture is presented that utilizes an HTL-free configuration with formamide tin iodide (FASnI3) as the active layer and fullerene (C60) as the electron transport layer (ETL), which represents a pioneering approach within the field. The elimination of hole transport layers (HTLs) reduces complexity and cost in PSC heterojunction structures, resulting in a simplified and more cost-effective PSC structure. In this context, an HTL-free tin HC(NH2)2SnI3-based PSC was simulated using the solar cell capacitance simulator (SCAPS) within a one-dimensional framework. Through this approach, the device performance of this novel HTL-free FASnI3-based PSC structure was engineered and evaluated. Key performance parameters, including the open-circuit voltage (Voc), short-circuit current density (Jsc), fill factor (FF), power conversion efficiency (PCE), I-V characteristics, and quantum efficiency (QE), were systematically assessed through the modulation of physical parameters across various layers of the device. A preliminary analysis indicated that the HTL-free configuration exhibited improved I-V characteristics, with a PCE increase of 1.93% over the HTL configuration due to improved electron and hole extraction characteristics, reduced current leakage at the back contact, and reduced trap-induced interfacial recombination. An additional boost to the device's key performance parameters has been achieved through the further optimization of several physical parameters, such as active layer thickness, bulk and interface defects, ETL thickness, carrier concentration, and back-contact materials. For instance, increasing the thickness of the active layer PSC up to 1500 nm revealed enhanced PV performance parameters; however, further increases in thickness have resulted in performance saturation due to an increased rate of hole-electron recombination. Moreover, a comprehensive correlation study has been conducted to determine the optimum thickness and donor doping level for the C60-ETL layer in the range of 10-200 nm and 1012-1019 cm-3, respectively. Optimum device performance was observed at an ETL-C60 ultra-thin thickness of 10 nm and a carrier concentration of 1019 cm-3. To maintain improved PCEs, bulk and interface defects must be less than 1016 cm-3 and 1015 cm-3, respectively. Additional device performance improvement was achieved with a back-contact work function of 5 eV. The optimized HTL-free FASnI3 structure demonstrated exceptional photovoltaic performance with a PCE of 19.63%, Voc of 0.87 V, Jsc of 27.86 mA/cm2, and FF of 81%. These findings highlight the potential for highly efficient photovoltaic (PV) technology solutions based on lead-free perovskite solar cell (PSC) structures that contribute to environmental remediation and cost-effectiveness.

Design of Homojunction Perovskite Solar-Cell Devices Without Hole-Transport Layer

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

A p‐p + Homojunction‐Enhanced Hole Transfer in Inverted Planar Perovskite Solar Cells

Dopant-Free Hole Transport Material Based on Non-Covalent Interaction for Efficient Perovskite Solar Cells

Design and simulation investigations on electron transport layer-free in tin-based p-n homojunction perovskite solar cells

A charge-separated interfacial hole transport semiconductor for efficient and stable perovskite solar cells

Towards Simplifying the Device Structure of High‐Performance Perovskite Solar Cells

Design of hole-transport-material free CH3NH3PbI3/CsSnI3 all-perovskite heterojunction efficient solar cells by device simulation

D-A-π-A-D-type Dopant-free Hole Transport Material for Low-Cost, Efficient, and Stable Perovskite Solar Cells

Advanced Optoelectronic Modeling and Optimization of HTL-Free FASnI3/C60 Perovskite Solar Cell Architecture for Superior Performance

Perovskite hetero-bilayer for efficient charge-transport-layer-free solar cells

Efficient Perovskite Solar Cells Enabled by Facile Synthesis of Triphenylamine‐Based Hole‐Transport Material with D–A1–A2 Structure

Hole transport layer-free carbon-based perovskite solar cells with high-efficiency up to 17.49% in air: From-bottom-to-top perovskite interface modification

Dopant‐Free Hole Transport Materials Based on a Large Conjugated Electron‐Deficient Core for Efficient Perovskite Solar Cells

Dopant-free hole-transporting materials based on a simple nonfused core with noncovalent conformational locking for efficient perovskite solar cells

Dopant‐Free Hole‐Transporting Material with Enhanced Intermolecular Interaction for Efficient and Stable n‐i‐p Perovskite Solar Cells

Targeted passivation and optimized interfacial carrier dynamics improving the efficiency and stability of hole transport layer-free narrow-bandgap perovskite solar cells

Surface Terminated 3D/2D Heterojunction Enables Efficient and Stable Perovskite Solar Cells

Dopant-Free Hole-Transporting Material Based on Poly(2,7-(9,9-bis(N,N-di-p-methoxylphenylamine)-4-phenyl))-fluorene for High-Performance Air-Processed Inverted Perovskite Solar Cells

Molecularly Tailored Perovskite/Poly(3-hexylthiophene) Interfaces for High-performance Solar Cells

Numerical modeling and performance optimization of carbon-based hole transport layer free perovskite solar cells