Abstract:In this study, a novel Ge-Sn based perovskite solar cell (PSC) with the structure FTO/WS2/ FA0.75MA0.25Sn0.95Ge0.05I3/MoO3/Ag has been designed and thoroughly analyzed employing SCAPS-1D. Drawing attention from the work of Ito et al., where a similar perovskite-based PSC displayed a poor performance of ~ 4.48 % PCE, in which a large conduction band offset (CBO) acts as a critical factor contributing to interfacial recombination and device deterioration. To address this issue, we presented WS2 as an electron transport layer (ETL) along with MoO3 as a hole transport layer (HTL), both possessing compatible CBO and valence band offset (VBO) with perovskite material. Through systematic simulations and optimizations, remarkable improvements in the PSC's performance have been acquired, getting a power conversion efficiency (PCE) of 18.97%. The optimized structure involved a 50 nm MoO3 HTL, 350 nm FA0.75MA0.25Sn0.95Ge0.05I3 light-harvesting layer (LHL), and a 50 nm WS2 ETL. Bulk defect densities for the LHL and ETL were optimized to 1×1015 cm-3 and 1×1018 cm-3, respectively, significantly superior values than that of reported value in the literature. Particularly, the tolerable defect density of ETL has increased 1000 times than published literature. The interfacial tolerable trap density for MoO3/perovskite increased from 1×1014 cm-2 to 1×1016 cm-2. The study also explored the impact of defects on quantum efficiency, revealing a severe negative influence beyond a perovskite bulk defect density of 1×1017 cm-3. Light intensity analysis demonstrated a correlation between incident light reduction and device performance decay. Capacitance–Voltage (C-V) and Mott-Schottky (M-S) have been analyzed during the study. Finally, the total recombination of the optimized device concerning thickness has been analyzed along with the dark J-V characteristics. The comprehensive insights gained from this work are anticipated to accelerate the fabrication of mixed Ge-Sn based PSCs with improved efficiency, paving the way for commercialization in the photovoltaic industry.

Numerical investigation of structural optimization and defect suppression for high-performance perovskite solar cells via SCAPS-1D

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Structural optimization of inverted CsPbI2Br perovskite solar cells for enhanced performance via SCAPS-1D simulation

Simulation in SCAPS-1D and optimization of a perovskite solar cell

Revealing the High-Performance of a Novel Ge-Sn-Based Perovskite Solar Cell by Employing SCAPS-1D

Numerical simulation and performance optimization of a lead-free inorganic perovskite solar cell using SCAPS-1D

Numerical analysis of ultra-thin MASnI3 based perovskite solar cell by SCAPS-1D

Performance optimization of CsPbIBr2-Based Perovskite Solar Cells through Device Modeling

Numerical simulation and optimization of CsPbI3-based perovskite solar cell to enhance the power conversion efficiency

Numerical analysis of high performance perovskite solar cells with stacked ETLs/C60 using SCAPS-1D device simulator

Synchronous Modulation of Defects and Buried Interfaces for Highly Efficient Inverted Perovskite Solar Cells

Enhanced efficiency of bifacial perovskite solar cells using computational study

Utilizing Density Functional Theory and SCAPS Simulations for Modeling High‐Performance MASnI3‐Based Perovskite Solar Cells

Defect and doping concentration study with series and shunt resistance influence on graphene modified perovskite solar cell: A numerical investigation in SCAPS-1D framework

Optimizing the working mechanism of the CsPbBr3-based inorganic perovskite solar cells for enhanced efficiency

Design and numerical investigation of efficient (FAPbI3)1−x(CsSnI3)x perovskite solar cell with optimized performances

Surface charge-transfer doping for highly efficient perovskite solar cells

Defect Investigation of Ti-Based Vacancy-Ordered Double Perovskite Solar Cell using SCAPS-1D

Direct Observation on <i>p</i>- to <i>n</i>-Type Transformation of Perovskite Surface Region during Defect Passivation Driving High Photovoltaic Efficiency

Design and simulation of CsPb.625Zn.375IBr2-based perovskite solar cells with different charge transport layers for efficiency enhancement

Enhancing the performance of perovskite solar cells through simple bilateral active site molecule assisted surface defect passivation