Abstract:This paper presents an investigation on the thermal damage characteristics and mechanism of carbon fiber reinforced polymer (CFRP) during fiber laser joining between CFRP and mild steel with Cr electroplating. The results show that laser heat causes non uniform thermal damage of CFRP at the bonding interface. In the center region of the fracture after shear testing of the joint, CFRP endures serious ablation characterized with the formation of large cavities and the joint failure happens at the bonding interface. In the peripheral region of the fracture, a large amount of micron porosities are observed and the joint failure happens at the porosity zone in CFRP. According to the thermochemical analysis of CFRP, the critical temperatures of resin matrix decomposition, carbon residue oxidation and carbon fiber oxidation are 350°C, 484°C and 650°C respectively. When the temperature is higher than 350°C, the resin matrix of CFRP decomposes, producing gaseous products such as CO2, NH3 and the water vapor, which form the porosities in CFRP. When the temperature is higher than 484°C, the residual carbon is oxidized and ablation happens. The thermal histories at different locations of bonding interface show that Gaussian distribution of the laser beam results in nonuniform temperature distribution in the bonding interface. The peak temperature in the center of bonding interface is 654°C,higher than the CFRP oxidation temperature. CFRP in this region endures severe thermo-oxidation ablation. In the peripheral region of the bonding interface, the peak temperature drops from 484°C to 350°C sharply with the increase of distance from the center line and CFRP in this region endures decomposition. Through strict control of laser heat input, the thermal ablation can be completely eliminated and the amount of the porosities can be reduced. Thus the shear strength of the joint is apparently improved from 16.8MPa to 27.2MPa.Therefore, using the laser with uniform intensity distributioninstead of fiber laserand controlling the temperature of interface lower than CFRP decomposition temperature is a promising approach to suppress the thermal damagein CFRP.

Effect of thermal damage on dynamic and static mechanical properties of CFRP short pulse laser hole cutting

Study on anisotropic heat transfer and thermal damage in nanosecond pulsed laser processing of CFRP

Hole Quality and Thermal Defects in Drilled CFRP by Nanosecond Pulsed Laser

The damage characteristics and mechanism of CFRP during laser joining of CFRP/mild steel dissimilar joint

Research progress on the quality and efficiency of carbon fiber reinforced thermoplastic polymer composites processed by laser

Dimethicone-assisted interlaced scanning compound cutting for regulating thermal damage in CFRP laser cutting by synergistic suppression of coupled heat effect

Study on the mechanism of quasi-continuous wave (QCW) fiber laser low-damage processing of carbon fiber-reinforced plastics

Assessment of laser cutting parameters and heat-affected zone on microstructure and fatigue behaviour of carbon fibre-reinforced epoxy

Experimental Study on Carbon Fiber-Reinforced Composites Cutting with Nanosecond Laser

Investigation of high temperature effect on CFRP cutting mechanism based on a temperature controlled orthogonal cutting experiment

Development of Laser Processing Carbon-Fiber-Reinforced Plastic

Mechanism and Behavior of Laser Irradiation on Carbon Fiber Reinforced Polyetheretherketone (CF/PEEK) During the Laser-Assisted In-Situ Consolidation Additive Manufacturing Process

Experimental study on CFRP drilling with the picosecond laser "double rotation" cutting technique

Study of experimental and numerical simulation of high-energy laser processing on carbon fiber reinforced polymer

Cracking Behavior of Cfrp Laminate-Strengthened Rc Beams with Premechanical and Postmechanical Environmental Damage

Experimental Investigation on Ablation Behaviors of CFRP Laminates in an Atmospheric Environment Irradiated by Continuous Wave Laser

Investigation of Heat Accumulation in Femtosecond Laser Drilling of Carbon Fiber-Reinforced Polymer

Damage characterization and discrimination in laser-shocked carbon fiber reinforced polymer laminates: A mass-spring-damping model approach

Reducing the taper and the heat-affected zone of CFRP plate by Micro fluid assisted laser induced plasma micro-drilling

Femtosecond Laser Drilling of Cylindrical Holes for Carbon Fiber-Reinforced Polymer (CFRP) Composites

Investigation on heat transfer and ablation mechanism of CFRP by different laser scanning directions