Abstract:Antimony sulfide thin films of thickness ≈500 nm have been deposited on glass slides from chemical baths constituted with SbCl3 and sodium thiosulfate. Smooth specularly reflective thin films are obtained at deposition temperatures from −3 to 10 °C. The differences in the film thickness and improvement in the crystallinity and photoconductivity upon annealing the film in nitrogen are presented. These films can be partially converted into a solid solution of the type Sb2SxSe3−x, detected in X-ray diffraction, through heating them in contact with a chemically deposited selenium thin film. This would decrease the optical band gap of the film from ≈1.7 eV (Sb2S3) to ≈1.3 eV for the films heated at 300 °C. Similarly, heating at 300 °C of sequentially deposited thin film layers of Sb2S3–Ag2Se, the latter also from a chemical bath at 10 °C results in the formation of AgSb(S/Se)2 with an optical gap of ≈1.2 eV. All these thin films have been integrated into photovoltaic structures using a CdS window layer deposited on 3 mm glass sheets with a SnO2:F coating (TEC-15, Pilkington). Characteristics obtained in these cells under an illumination of 850 W/m2 (tungsten halogen) are as follows: SnO2:F–CdS–Sb2S3–Ag(paint) with open circuit voltage (Voc) 470 mV and short circuit current density (Jsc) 0.02 mA/cm2; SnO2:F–CdS–Sb2S3–CuS–Ag(paint), Voc≈460 mV and Jsc≈0.4 mA/cm2; SnO2:F–CdS–Sb2SxSe3−x–Ag(paint), Voc≈670 mV and Jsc≈0.05 mA/cm2; SnO2:F–CdS–Sb2S3–AgSb(S/Se)2–Ag(paint), Voc≈450 mV and Jsc≈1.4 mA/cm2. We consider that the materials and the deposition techniques reported here are promising toward developing ‘all-chemically deposited solar cell technologies.’

Synthesis and characterization of In 2 S 3 : Na thin films prepared by vacuum thermal evaporation technique for photovoltaic applications

Characterization of Thermally Evaporated In2S3 Films for Solar Cell Application

Optical Properties of Thermally Evaporated in 2 S 3 Thin Films Measured Using Photoacoustic Spectroscopy

Synthesis and Characterization of In2s3 Nanocrystalline Material for Photovoltaic Application

PHOTOTHERMAL DEFLECTION ANALYSIS OF [math]-In2S3 THIN FILMS: THE EFFECT OF S/In MOLAR RATIOS

Preparation and characterization of Sb2Se3 thin films prepared by electrodeposition for photovoltaic applications

Growth of Polycrystalline In2S3 Thin Films by Chemical Bath Deposition Using Acetic Acid As a Complexing Agent for Solar Cell Application

Optoelectronic Properties of In2S3 Thin Films Measured Using Surface Photovoltage Spectroscopy

Synthesis and Physical Behaviour of In2S3 Films

Preparation of In_2S_3 Thin Films by Ultrasonic Spray Pyrolysis and the Influence of Post Rapid Thermal Process

Antimony sulfide thin films in chemically deposited thin film photovoltaic cells

Thickness Dependent Physical Properties of Close Space Evaporated In2S3 Films

Optical, electrical and electronic properties of SnS thin films deposited by sol gel spin coating technique for photovoltaic applications

Fabrication of In2S3 and In–Ga–S Thin Films via Atmosphere‐Controlled Fine‐Channel Mist Chemical Vapor Deposition

Annealing and Plasma Treatment Effect on Structural, Morphological and Topographical Properties of Evaporated Β-In2s3 Films

SnS Films for Photovoltaic Applications: Physical Investigations on Sprayed SnxSy Films

Effect of Substrate Temperature on Structural and Optical Properties of In2S3 Thin Films Grown by Thermal Evaporation

Influence of post-annealing in sulfur atmosphere on thermally evaporated β-In2S3 films

One Pot Synthesis of Sb2S3 Nanocrystalline Films Through a PVP-assisted Hydrothermal Process

Synthesis and Characterization of NaSbS 2 Thin Film for Potential Photodetector and Photovoltaic Application

In Situ Growth of In2S3 Nanorods in Poly(3-Hexylthiophene) Hybrid Films