Abstract:In present study, the creep behavior of (TiB + TiC+Y2O3)/α-Ti composite with C-1 and C-2 microstructure were investigated with applied stress of 200 MPa and at 650–700 °C. The steady state creep rate increased by an order of magnitude from 650 °C to 700 °C, and the C-2 microstructure shown worse creep performance compared to C-1 microstructure. The creep activation energy of C-1 and C-2 microstructure were 359.5 kJ/mol and 380.2 kJ/mol, respectively, which were higher than the lattice diffusion in α-Ti. And the less QG due to coarse microstructure was responsible for its higher creep activation energy in C-2. In addition to cracks were observed at β grain boundary, α colony boundary, α/β phase boundary, they were also observed near the fracture TiB whiskers and near decohesion reinforcements. The cracks in C-2 were mainly concentrated near the reinforcement, while those in C-1 were mainly concentrated in the matrix part. Further analysis confirmed that the creep deformation mechanism of C-2 microstructure was controlled by reinforcements, but the creep deformation mechanism of C-1 microstructure was controlled by matrix microstructure. Summarily, the effect of reinforcement on creep deformation of (TiB + TiC+Y2O3)/α-Ti composite could be divided in two aspect: microstructure influence and the reinforcement itself. For reinforcement itself, it indeed affected the dislocation movement and creep fracture behavior, and then improved the creep performance. However, for microstructure influence, the fine grain (more grain boundary), coarsen microstructure (more equiaxed characteristics of α lamellar) caused more grain boundary slip to participate in creep deformation, which in turn deteriorated creep performance. In this study, the latter effect was somewhat bigger.

Compressive creep properties and mechanisms of (Ti-Zr-Nb-Ta-Mo)C high entropy ceramics at high temperatures

Temperature-dependent mechanical properties of TaC and HfC

Tensile creep behavior of HfNbTaTiZr refractory high entropy alloy at elevated temperatures

Mechanical properties and high-pressure behavior of high entropy carbide (Mo, Nb, Ta, V, W)C

Unveiling the Microstructure Evolution and the Short-Time Tensile Creep Behavior in the CuCrZr Alloy

Mechanical and tribological performance of (TiNbTaWMo)C high-entropy ceramics in a wide temperature range

The creep behavior of (TiB + TiC + Y2O3)/α-Ti composites at high temperature and short-term

Low temperature densification mechanism and properties of Ta1-Hf C solid solutions with decarbonization and phase transition of Cr3C2

Frist-principles prediction of elastic, electronic, and thermodynamic properties of high entropy carbide ceramic (TiZrNbTa)C

A practical guideline for designing high-entropy carbides based on (Ti1/3Mo1/3W1/3)C with high valence electron concentration

Microstructure, Mechanical and Tribological Properties of High-Entropy Carbide (MoNbTaTiV)C5

Microstructures and mechanical properties of high-entropy (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C ceramics with the addition of SiC secondary phase

The effect of submicron grain size on thermal stability and mechanical properties of high‐entropy carbide ceramics

Annealing of a (Hf0.2Ta0.2Ti0.2Nb0.2Zr0.2)C high-entropy ceramic up to 2100 °C: In-situ removal of oxide impurities and microstructural modification

Intermediate-Temperature Creep Deformation and Microstructural Evolution of an Equiatomic FCC-Structured CoCrFeNiMn High-Entropy Alloy

Elasticity, mechanical and thermal properties of polycrystalline hafnium carbide and tantalum carbide at high pressure

Microstructures and mechanical properties of (Nb0.25Mo0.25Ta0.25W0.25)C and (Nb0.2Mo0.2Ta0.2W0.2Hf0.2)C high-entropy carbide ceramics produced by arc melting

Elevated-temperature Deformation Mechanisms in a CrMnFeCoNi High-Entropy Alloy

Insights into High‐Temperature Uniaxial Compression Deformation Behavior of Ti3AlC2

Strength of single‐phase high‐entropy carbide ceramics up to 2300°C

Low-temperature densification of high-entropy (Ti,Zr,Nb,Ta,Mo)C—Co composites with high hardness and high toughness