Abstract:Bismuth telluride-based alloys are the best performing thermoelectric materials near room temperature. Grain size refinement and nanostructuring are the core stratagems for improving thermoelectric and mechanical properties. However, the donor-like effect induced by grain size refinement strongly restricts the thermoelectric properties especially in the vicinity of room temperature. In this study, the formation mechanism for the donor-like effect in Bi2Te3-based compounds was revealed by synthesizing five batches of polycrystalline samples. We demonstrate that the donor-like effect in Bi2Te3-based compounds is strongly related to the vacancy defects (VBi‴ and VTe···) induced by the fracturing process and oxygen in air for the first time. The oxygen-induced donor-like effect dramatically increases the carrier concentration from 2.5 × 1019 cm-3 for the zone melting ingot and bulks sintered with powders ground under an inert atmosphere to 7.5 × 1019 cm-3, which is largely beyond the optimum carrier concentration and seriously deteriorates the thermoelectric performance. Moreover, it is found that both avoiding exposure to air and eliminating the thermal vacancy defects (VBi‴ and VTe···) via heat treatment before exposure to air can effectively remove the donor-like effect, producing almost the same carrier concentration and Seebeck coefficient as those of the zone melting ingot for these samples. Therefore, a defect equation of oxygen-induced donor-like effect was proposed and was further explicitly corroborated by positron annihilation measurement. With the removal of donor-like effect and improved texturing via multiple hot deformation (HD) processes, a maximum power factor of 3.5 mW m-1 K-2 and a reproducible maximum ZT value of 1.01 near room temperature are achieved. This newly proposed defect equation of the oxygen-induced donor-like effect will provide a guideline for developing higher-performance V2VI3 polycrystalline materials for near-room-temperature applications.

Recovery and thermoelectric performance optimization of p-type bismuth telluride waste by secondary zone-melting

Improved thermoelectric properties of zone-melted p-type bismuth-telluride-based alloys for power generation

Organic/Inorganic Hybrid Design as a Route for Promoting the Bi<sub>0.5</sub>Sb<sub>1.5</sub>Te<sub>3</sub> for High-Performance Thermoelectric Power Generation

Performance Boost for Bismuth Telluride Thermoelectric Generator Via Barrier Layer Based on Low Young’s Modulus and Particle Sliding

Performance boost for bismuth telluride thermoelectric generator via barrier layer based on low Young's modulus and particle sliding

Tunable Optimum Temperature Range of High-Performance Zone Melted Bismuth-Telluride-Based Solid Solutions

Enhanced thermoelectric performance of p-type sintered BiSbTe-based composites with AgSbTe2 addition

Enhanced Thermoelectric Performance of P‐Type (Bi,Sb)2Te3 by Incorporating Non‐Stoichiometric Ag5Te3 and Refining Te‐Se Ratio

Achieving High Thermoelectric Performance in p-Type BST/PbSe Nanocomposites through the Scattering Engineering Strategy

High Thermoelectric Performance Bismuth Telluride Prepared by Cold Pressing and Annealing Facilitating Large Scale Application

Spark plasma sintered Bi-Sb-Te alloys derived from ingot scrap: Maximizing thermoelectric performance by tailoring their composition and optimizing sintering time

Efficient Separation and Purification Method for Recovering Valuable Elements from Bismuth Telluride Refrigeration Chip Waste

Thermoelectric Performance of P-Type Zone-Melted Se-doped Bi 0.5 Sb 1.5 Te 3 Alloys

Microstructure Evolution in Plastic Deformed Bismuth Telluride for the Enhancement of Thermoelectric Properties

Significant Enhancement of Thermoelectric Figure of Merit in BiSbTe‐Based Composites by Incorporating Carbon Microfiber

Critical Role of Tellurium Self-Compensation in Enhancing the Thermoelectric Performance of P-Type Bi0.4Sb1.6Te3 Alloy

Enhanced Thermoelectric Performance of Solution-Derived Bismuth Telluride Based Nanocomposites Via Liquid-Phase Sintering

Tuning Multiscale Microstructures to Enhance Thermoelectric Performance of N‐type Bismuth‐Telluride‐Based Solid Solutions

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi0.48Sb1.52Te3-AgSbSe2 Composite.

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi 0.48 Sb 1.52 Te 3 –AgSbSe 2 Composite

Removing the Oxygen-Induced Donor-like Effect for High Thermoelectric Performance in n-Type Bi 2 Te 3 -Based Compounds