Abstract:Ti-6Al-4V parts are usually hypothesized as isotropic mechanical properties during micro-machining operation. However, the crystal anisotropic mechanical property is an influential factor in the machining of crystals with different sizes and orientations. The hypothesis causes distinct variation in predicting machining force, and consequently the surface integrity cannot be exactly predicted in the micro-machining. Actually, Ti-6Al-4V parts are pseudo isotropy composed of grains with different orientations, elastic modulus, and hardness. Simultaneously, the initiation mode of plastic slip system varies with the grain orientation when the crystal is subjected to an applied load. It is challengeable to evaluate the effect of crystal orientation on its macroscopic properties, either by traditional experimental methods or macroscopic finite element analysis. Nano-indentation provides one novel method to investigate the plastic deformation of selected grains with specific orientations to characterize their mechanical response properties. This research aims to investigate the plastic behavior of α phase Ti-6Al-4V with different orientation grains by means of nano-indentation experiment and crystal plastic finite element method. In the study, single crystals of α phase are classified into “hard grains” (θ < 30°), “soft grains” (θ > 60°) and “normal grains” (30° < θ < 60°) by defining the crystal inclination angle (θ). The elastic modulus and hardness of hard grains are 9% and 28% larger than those of soft grains, respectively. This difference in mechanical properties depends on the slip system that dominates the plastic deformation behavior. The plastic deformation of soft grains is dominated by prismatic slip (48%), while hard grains are accommodated to plastic deformation by basal slip (51%). The average total cumulative shear strain of the soft grains is double that of the hard grains at a maximum load of 10 mN. Meanwhile, the sensitivity analysis is performed to evaluate the effects of the three sets of < a > slip systems and the two sets of < c + a > slip systems on plastic deformation with different grain orientations. The research contributes to the understanding of the plastic deformation mechanism in micro-machining and the exactly predicting the surface integrity generated from micro-machining.

An investigation of phase boundary effect on the cutting force fluctuation in orthogonal micro-cutting of Ti6Al4V alloy

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Microstructure alteration in the high-speed machining of titanium alloy involved with tool wear and cryogenic condition

Microstructure Effects on Surface Integrity in Slot Micro-Milling Multiphase Titanium Alloy Ti6Al4V

Investigation on the Crystal Plasticity of Α Phase Ti-6Al-4V Based on Nano-Indentation Simulation and Experiment

Atomic simulation for the effect of nano-cutting parameters on the 3D surface morphology of polycrystalline γ-TiAl alloy

A Simulation Study on the Effect of Micro-Textured Tools During Orthogonal Cutting of Titanium Alloy Ti-6Al-4V

Experimental study on fracture mechanism transformation in chip segmentation of Ti-6Al-4V alloys during high-speed machining

Microstructural modulation of TiAl alloys for controlling ultra-precision machinability

Molecular dynamics simulation of the effect of tool parameters on nano-cutting of polycrystalline γ-TiAl alloys

The influence of cutting parameters on the defect structure of subsurface in orthogonal cutting of titanium alloy

Dislocation Dynamics-Based Modeling And Simulations Of Subsurface Damages Microstructure Of Orthogonal Cutting Of Titanium Alloy

Effect of phase boundary on the critical resolved shear stress and dislocation behavior of dual-phase titanium alloy

Numerical simulation of nano-cutting behaviors for polycrystalline γ-TiAl alloy: The effect of grain sizes

Microstructure evolution modeling of Ti6Al4V alloy during cutting using the Particle Finite Element Method and homogeneous field distributions

Molecular dynamics simulation of cutting mechanism of polycrystalline Fe-Cr-W alloy

Analysis of the effect of tool geometry on the cutting process of polycrystalline Fe-Cr-W alloy based on molecular dynamics simulation

Orientation effect on / phase interface mediated deformation mechanism in titanium alloy

Study on phase transformation in cutting Ni-base superalloy based on molecular dynamics method

Experimental and Multiscale Numerical Investigation of Wear Mechanism and Cutting Performance of Polycrystalline Diamond Tools in Micro-End Milling of Titanium Alloy Ti-6Al-4V

The influence of the material behaviour law parameters and thermal properties on the chip morphology: application to the orthogonal cutting of Ti6Al4V alloy