Abstract:The durability of infrastructure materials, such as concrete, has direct impact on society because the productivity of many industries and safety of human beings depend on infrastructure condition, and further because maintenance of the infrastructure can represent a significant portion of a government’s budget. Thus the enhancement of concrete durability and improvement of infrastructure condition monitoring are significant concerns to the scientific community. The resonant frequency method has been traditionally used to assess the mechanical condition of concrete. Resonance frequencies of a solid body depend on test sample mass and dimensions, elastic properties, and boundary conditions. Resonance frequencies have been used to determine engineering properties such as the elastic moduli and material damping. The method is useful to assess the performance of materials within accelerated degradation durability test procedures, and to inspect quality of the products during manufacturing processes (pass/fail tests). Different testing standards and recommendations prescribe test configurations, and specific tests are recommended for different materials. A basic resonant frequency test requires a forced vibration system to set up mechanical resonances, and some system to sense the frequency content from the resonant vibration signals. For concrete-like materials, these specifications are given by ASTM C215 [1], wherein an impulsive impact event is applied to the test sample to excite the resonant frequencies and a small sensor is mounted on the surface of the test sample. From the impulsive impact vibration signals thus obtained, two standard parameters are usually derived: (1) the dynamic modulus, which depends on sample dimensions, mass, and the resonant frequency peak (f), and (2) the attenuation or damping capacity of the material. Figure 12.1a, b illustrates typical signals obtained from a single-impact vibration test, where the spectral (frequency domain) signal is computed from the time signal using a Fourier transform algorithm. The continuous reduction of the vibration signal amplitude with time during the signal “ring-down” is seen in the time domain signal. The resonant frequency and damping characteristics are extracted from the spectral signal in the region around the resonant frequency peak. The damping capacity of the material is determined from the quality factor (Q) (or inverse attenuation), which is defined as the ratio between the resonant frequency peak (f) and the bandwidth frequencies corresponding to a 50% reduction of vibration energy in the power frequency spectrum for a given vibration mode [2]. Meaningful application of the ASTM C215 test is found within other standard durability test methods [3, 4].

An acousto-ultrasonic approach for the determination of water-to-cement ratio in concrete

Water Content Diagnostics of Concrete Using Nonlinear Acoustics Means

Ultrasonic assessment of compressive strength of underwater concrete considering various mix parameters

Application of Infrared Spectroscopy in the Measurement of Carbonation Depth of Concrete

A solitary wave-based sensor to monitor the setting of fresh concrete

Ultrasonic monitoring of the early-age hydration of mineral admixtures incorporated concrete using cement-based piezoelectric composite sensors

Study of the Healing Effect of Concrete with Supplementary Cementitious Materials after Early-Age Damage by Acoustic Emission Technique

Analysis of coherent surface wave dispersion and attenuation for non-destructive testing of concrete

A two stage procedure for assessment of in situ concrete strength using combined non-destructive testing

Non-Destructive Inspection of Concrete Structures by Ultrasonic Sensor Based on a Frequency Analysis

Acoustic emission analysis applied to concrete under different loading

Mechanical Properties of Concrete Produced with Coarse Aggregates from Different Mineralogical Origins Using Ultrasonic Tests

Acoustic Emission for Determining Early Age Concrete Damage as an Important Indicator of Concrete Quality/Condition before Loading

Simulations of ultrasonic wave propagation in concrete based on a two-dimensional numerical model validated analytically and experimentally

Non-destructive concrete strength evaluation using smart piezoelectric transducer—a comparative study

Investigation of Self-Compacting Concrete Behavior under Axial Load by Acoustic Emission Method

Ultrasonic monitoring of hydration behavior of cement paste doped with triethanolamine using novel piezoelectric ultrasonic transducer

Estimation of compressive strength of concrete structures using the ultrasonic pulse velocity method and spectral analysis of surface wave method

Ultrasonic Coda Wave Monitoring of Alkali-Silica Reactivity in Concrete Laboratory Prisms

Monitoring the curing process of in-situ concrete with piezoelectric-based techniques – A practical application

Cement-Based Material Characterization Using Nonlinear Single-Impact Resonant Acoustic Spectroscopy (NSIRAS)