HIV infection in greek intravenous drug users

G. Papaevangelou,A. Roumeliotou,G. Stergioy,A. Nestoridou,E. Trichopoulou,G. Kallinikos,G. Rizos,E. Kornarou

DOI: https://doi.org/10.1007/BF00221347

European Journal of Epidemiology

Abstract:

What problem does this paper attempt to address?

Monitoring the curing process of in-situ concrete with piezoelectric-based techniques – A practical application

Zi Sheng Tang,Yee Yan Lim,Scott T. Smith,Ahmed Mostafa,Ah Choi Lam,Chee Kiong Soh

DOI: https://doi.org/10.1177/14759217221087916

2022-05-21

Structural Health Monitoring

Abstract:Structural Health Monitoring, Ahead of Print. The stiffness and strength properties of freshly poured concrete develop over time as the concrete hardens due to curing. The monitoring of such properties therefore enables timely construction decisions such as formwork removal. Traditional point-in-time destructive tests can be cumbersome, while continuous non-destructive testing is desirable. Piezoelectric-based electromechanical impedance (EMI) and wave propagation (WP) techniques fall into the latter, and they have been verified for monitoring concrete properties during curing in the laboratory. This paper reports the first field application of the EMI and WP techniques for monitoring concrete curing, where smart aggregate (SA) sensors are embedded into concrete pour strips of a multi-storey residential building during construction. For comparison and verification purposes, destructive compression and non-destructive ultrasonic pulse velocity (UPV) tests were conducted. Results obtained from both EMI and WP techniques were consistent and repeatable. They were also comparable to the UPV result, and they showed a close correlation to the compressive strength tests. The current study has also revealed that the electrical signatures acquired from the EMI and WP techniques have a linear relationship. EMI-based and WP-based semi-analytical models (and their derivations) that can quantify the compressive strength and modulus of elasticity of concrete at various curing durations are also presented. This reported study ultimately demonstrates the applicability and practical application of the EMI and WP techniques for real-time measurements, bridging the gap between laboratory-based studies and field applications.
Monitoring the Setting Process of Cementitious Materials Using Guided Waves in Thin Rods

Dongquan Wang,Guangyun Yu,Shukui Liu,Ping Sheng

DOI: https://doi.org/10.3390/ma14030566

IF: 3.4

2021-01-25

Materials

Abstract:Characterizing early-age properties is very important for the quality control and durability of cementitious materials. In this paper, an approach using embedded guided waves was adopted to monitor the changes in the mechanical proprieties of mortar and concrete during setting, and embedded thin rods with low-cost piezoelectric sensors mounted on top were used for guide wave monitoring. Through continuous attenuation monitoring of the guided waves, the evolution of mortar and concrete properties was characterized. Four different kinds of metallic rods were tested at the same time to find out the optimal setup. Meanwhile, shear wave velocities of the mortar and concrete samples were monitored and correlated to the attenuation, and setting time tests were also performed on these samples. Experimental results demonstrate that the proposed approach could monitor the evolution of the setting of cementitious materials quantitatively, and time of the initial setting could be determined by this technique as well. In addition, it is found that the attenuations of fundamental longitudinal guided wave mode are almost the same in concrete samples and mortar samples sieved from concrete, indicating that this technique is able to eliminate the effects of coarse aggregates, which makes it of great potential for in-situ monitoring of early age concrete.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
New Directions in Concrete Health Monitoring Technology

Surendra P. Shah,John S. Popovics,Kolluru V. Subramaniam,Corina-Maria Aldea

DOI: https://doi.org/10.1061/(asce)0733-9399(2000)126:7(754)

2000-07-01

Journal of Engineering Mechanics

Abstract:The NSF-sponsored Center for Advanced Cement-Based Materials is actively involved in research aimed at the development of technologies for health monitoring and nondestructive evaluation of the concrete infrastructure. This paper summarizes pertinent research performed at the center. Basic findings from several new laboratory-based nondestructive evaluation techniques for concrete are reported. The described techniques are based on measurements of mechanical waves that propagate in the concrete. First, ultrasonic longitudinal wave (also called the L-wave or P-wave) signal transmission (attenuation) measurements are shown to be sensitive to the presence of damage in the form of distributed cracking in concrete. Next, experimental procedures that enable practical one-sided wave signal transmission measurements to be performed on concrete structures are described. The utility of the signal transmission measurement is demonstrated by two experimental test series; the depths of surface-opening cracks in concrete slabs are estimated and the extent and nature of autogenous healing in concrete disks are studied. Finally, an approach by which fatigue-induced damage in concrete structures is nondestructively monitored is described. Vibration frequencies are shown to be sensitive to the presence of fatigue-induced cracking in concrete specimens; changes in the vibration frequency of a concrete specimen during fatigue tests are related to the remaining fatigue life of the test specimens.

engineering, mechanical
Non-destructive concrete strength evaluation using smart piezoelectric transducer—a comparative study

Yee Yan Lim,Kok Zee Kwong,Willey Yun Hsien Liew,Chee Kiong Soh

DOI: https://doi.org/10.1088/0964-1726/25/8/085021

IF: 4.1

2016-07-18

Smart Materials and Structures

Abstract:Concrete strength monitoring, providing information related to the readiness of the structure for service, is important for the safety and resource planning in the construction industry. In this paper, a semi-analytical model of surface bonded piezoelectric (lead zirconate titanate) based wave propagation (WP) technique was developed for strength evaluation of mortar with different mix, throughout the curing process. Mechanical parameters of the mortar specimen were mathematically evaluated from the surface wave (R-wave) and pressure wave (P-wave) using elastic wave equations. These parameters were then empirically correlated to the strength. The model was found to be very robust as it could be generalized to account for different water to cement (W/C) ratio. The performance of the WP technique was then compared to the electromechanical impedance technique and other conventional techniques, such as the ultrasonic pulse velocity (UPV) test and the rebound hammer test. Results showed that the WP technique performed equally well as the conventional counterparts. The proposed technique is also advantageous over embedded WP technique and the UPV test, in terms of its capability to capture two types of waves for the evaluation of dynamic modulus of elasticity and Poisson's ratio. A separate study was finally conducted to verify the applicability of this technique on heterogeneous concrete specimen. With the inherent capability of the WP technique in enabling autonomous, real-time, online and remote monitoring, it could potentially replace its conventional counterparts, in providing a more effective technique for the monitoring of concrete strength.

materials science, multidisciplinary,instruments & instrumentation
Electrical Based Sensors and Remote Monitoring System for Assessing the Corrosion Related Activity in Concrete at Hangzhou Bay Bridge

Sudarsan Srinivasan,Muhammed Basheer,Jianghong Mao,Weiliang Jin,W. J. McCarter,Kang Li

2012-01-01

Abstract:Concrete structures in marine environments are subjected to cyclic wetting and drying, corrosion of reinforcement due to chloride ingress and biological deterioration. In order to assess the quality of concrete and predict the corrosion activity of reinforcing steel in concrete in this environment, it is essential to monitor the concrete continuously right from the construction phase to the end of service life of the structure. In this paper a novel combination of sensor techniques which are integrated in a sensor probe is used to monitor the quality of cover concrete and corrosion of the reinforcement. The integrated sensor probe was embedded in different concrete samples exposed to an aggressive marine environment at the Hangzhou Bay Bridge in China. The sensor probes were connected to a monitoring station, which enabled the access and control of the data remotely from Belfast, UK. The initial data obtained from the monitoring station reflected the early age properties of the concretes and distinct variations in these properties were observed with different concrete types. Corresponding author’s email: s.srinivasan@qub.ac.uk
A novel ultrasonic-velocity-based concrete carbonation monitoring method based on step-wise stretching technique

Xiangtao Sun,Shanchang Yi,Xiuquan Li,Yongxiang Cui,Minghui Zhang,Tianyong Jiang,Lei Wang,Qingzhao Kong

DOI: https://doi.org/10.1177/14759217241282481

2024-10-26

Structural Health Monitoring

Abstract:Structural Health Monitoring, Ahead of Print. Carbonation is a common and slow process that occurs in cement-based material, resulting in durability degradation of reinforced concrete structures. In this research, the relative velocity change (dv/v) of both ultrasonic direct waves and coda waves are extracted based on the step-wise stretching method for concrete carbonation monitoring. To this end, two-dimensional mesoscale models are established to investigate the ultrasonic propagation behaviors and assess the effectiveness of direct waves and coda waves on concrete carbonation monitoring. The numerical results indicate that direct waves could evaluate the initial carbonation, but exhibit limited sensitivity for severe carbonation. Conversely, the dv/v values of coda waves show a linear correlation with carbonation depth in all conditions. Accelerated concrete carbonation experiments are conducted to validate the numerical findings. The experimental results and numerical findings mutually corroborate, validating the effectiveness of velocity changes of coda waves on all-stage concrete carbonation monitoring. This research contributes a novel method for monitoring concrete carbonation and enhances the understanding of ultrasonic wave propagation in concrete.

engineering, multidisciplinary,instruments & instrumentation
Piezoelectric-based non-destructive monitoring of hydration of reinforced concrete as an indicator of bond development at the steel–concrete interface

R. Tawie,H.K. Lee

DOI: https://doi.org/10.1016/j.cemconres.2010.08.011

IF: 11.958

2010-12-01

Cement and Concrete Research

Abstract:Advances in piezoelectric materials have attracted interests among researchers to develop new non-destructive evaluation and monitoring techniques. In this study, piezoceramic (PZT) sensors were embedded in concrete by bonding the sensors on steel reinforcing bars to perform non-destructive monitoring. To evaluate the performance of the PZT sensors and electromechanical impedance (EMI) sensing technique, a series of experiments was carried out to monitor the bond development between steel rebar and concrete by measuring the electrical response of the PZT bonded to the steel rebar using an impedance analyzer. From the EMI measurements, the gradual adhesion between the steel rebar and fresh concrete could be detected via the measured changes in the conductance spectra of the PZT sensor bonded to the steel rebar. The bond development could be attributed to the transformation of concrete from liquid to solid state controlled by the hydration of cement and by monitoring the hydration of concrete with respect to time, the status of bonding can be estimated. The results show that the early-age development of bonding between steel rebar and concrete is affected by various factors such as varying water–cement ratio, low curing temperature and poor compaction.

construction & building technology,materials science, multidisciplinary
Establishment of a Mass Concrete Strength-Monitoring Method Using Barium Titanate–Bismuth Ferrite/Polyvinylidene Fluoride Nanocomposite Piezoelectric Sensors with Temperature Stability

Guoliang Lin,Dongwang Lu,Bowen Cui,Aoxiang Lin,Minyi Liu,Yongbin Ye

DOI: https://doi.org/10.3390/s24144653

IF: 3.9

2024-07-18

Sensors

Abstract:Mass concrete is widely used in large-scale projects, including metro upper cover structures, water conservancy dams, and heavy equipment foundations, among others, necessitating the process of health monitoring in mass concrete construction. The development of reliable and simple strength-monitoring methods for mass concrete is challenging because the inner temperature of mass concrete is high and changes a lot. This study proposes a strength-monitoring approach for mass concrete using barium titanate–bismuth ferrite/polyvinylidene fluoride (BT–BFO/PVDF) nanocomposite piezoelectric sensors, wherein the new sensors are embedded as actuators and sensors in mass concrete. The stress wave generated by the BT–BFO/PVDF piezoelectric sensors is used to monitor the specimen's strength for 28 days. The piezoelectric voltage received by the sensors in mass concrete is analyzed. The experimental results indicate that the signal received by the BT–BFO/PVDF sensors is not easily affected by the internal temperature of mass concrete compared with that of the traditional PVDF piezoelectric sensors. The signal parameters sensitive to concrete strength variation and the change trend of concrete strength are closely related to the piezoelectric voltage. Therefore, the proposed approach using BT–BFO/PVDF nanocomposite piezoelectric sensors is efficient (error < 10%) in mass concrete monitoring. Moreover, the monitoring results do not need temperature compensation. The physical meaning of the obtained strength prediction formula is proposed. An experimental system based on PVDF dynamic strain-sensing characteristics is established.

engineering, electrical & electronic,instruments & instrumentation,chemistry, analytical
Piezoelectric sensor based nondestructive active monitoring of strength gain in concrete

Sung Woo Shin,Adeel Riaz Qureshi,Jae-Yong Lee,Chung Bang Yun

DOI: https://doi.org/10.1088/0964-1726/17/5/055002

IF: 4.1

2008-07-18

Smart Materials and Structures

Abstract:The recent advent of smart materials, such as piezoelectric materials, shape-memory alloys, and optical fibers, has added a new dimension to present structural health monitoring techniques. In particular, the electro-mechanical impedance (EMI) sensing technique utilizing piezoelectric materials has emerged as a potential tool for the implementation of a built-in monitoring system for damage detection of civil structures. However, there is little effort to apply this technique for concrete monitoring. In this study, an effort to extend the applicability of the EMI sensing technique is made for strength gain monitoring of early age concrete. PZT (piezoelectric lead zirconate titanate) patches are employed to sense the EMI signature of curing concrete. A series of experiments was conducted on concrete specimens to verify the applicability of the EMI sensing technique. The results show the excellent potential of the EMI sensing technique as a practical and reliable nondestructive method for strength gain monitoring.

materials science, multidisciplinary,instruments & instrumentation
Application of Distributed Optical Fiber Sensing Technology to the Detection and Monitoring of Internal Swelling Pathologies in Massive Concrete Blocks

Ismail Alj,Marc Quiertant,Aghiad Khadour,Quentin Grando,Karim Benzarti

DOI: https://doi.org/10.3390/s22207797

2022-10-14

Abstract:This paper presents an experimental application of Distributed Optical Fiber Sensors (DOFS) for the Structural Health Monitoring (SHM) of concrete structures affected by internal swelling pathologies. In the framework of a large research project aiming to assess the possible extension of the operating lifetime of nuclear power plants from 40 to 60 years, massive blocks were cast from reactive concrete mixtures intended to develop delayed ettringite formation and alkali-silica reaction. These blocks were subjected to specific ageing conditions to initiate and accelerate the concrete pathologies. Some of the blocks were instrumented with DOFS bonded to the surface and embedded in the concrete. Using an interrogator device based on Rayleigh backscattering and a suitable procedure to eliminate temperature effects, distributed strain measurements were then performed at different time intervals. The first results of this ongoing study made it possible to demonstrate the feasibility and effectiveness of this sensing technology for detecting and monitoring expansion induced by swelling pathologies in representative-scale concrete structures.
Monitoring of Strength Gain in Concrete Using Smart Pzt Transducers

Adeel Riaz Qureshi,Sung Woo Shin,Chung Bang Yun

2007-01-01

Abstract:This paper presents the feasibility of using electromechanical impedance based active sensing technique for nondestructive strength gain monitoring of early-age concrete by employing piezoelectric lead-zirconate-titanate (PZT) patches on concrete surface. The strength development of early age concrete is actively monitored by performing a series of experiments on concrete specimens under moist curing condition. The electrical admittance signatures are acquired for five different curing ages and compared with each other. The resonant frequency shifts of PZT patches with increasing days is observed which is on account of additional stiffening due to strength gain of concrete during curing and level of stiffening being related to strength obtained from compression tests on companion cylinder specimens. The proposed approach is found to be suitable for monitoring the development of compressive strength in early-age concrete. It is also observed in this study that root mean square deviation (RMSD) in admittance signatures of the PZT patches can also be used as an indicator of concrete strength development.
Wireless strain and temperature monitoring in reinforced concrete using Surface Acoustic Wave (SAW) sensors

Pierre Jeltiri,Firas Al-Mahmoud,Rémi Boissière,Baptiste Paulmier,Tony Makdissy,Omar Elmazria,Pascal Nicolay,Sami Hage-Ali

DOI: https://doi.org/10.1109/LSENS.2023.3315219

2023-10-02

Abstract:Monitoring the health of civil engineering structures using implanted deformation, temperature and corrosion sensors would further improve maintenance and extend the service life of those structures. However, sensor integration poses a number of problems, due to the presence of cables and on-board electronics. Passive, wireless SAW sensors offer a very promising solution, here. We used commercial SAW devices mounted on steel rebars to carry out an initial feasibility study. Without cables or embedded electronics, we were able to measure the deformation of a concrete beam subjected to bending load. We were also able to measure the temperature continuously over a three-week period.

Signal Processing
Embedded Wireless Sensor for In Situ Concrete Internal Relative Humidity Monitoring

Tai Ikumi,Ignasi Cairó,Jan Groeneveld,Antonio Aguado,Albert de la Fuente

DOI: https://doi.org/10.3390/s24061756

IF: 3.9

2024-03-09

Sensors

Abstract:The moisture content within the concrete pore network significantly influences the mechanical, thermal, and durability characteristics of concrete structures. This paper introduces a novel fully embedded wireless temperature and relative humidity sensor connected to an automatic acquisition system designed for continuous concrete monitoring. Relative humidity measurements from this new sensor are compared with those obtained by a commercial system based on the borehole method at different depths (2.5 and 4.0 cm) and exposure conditions (oven drying and humid chamber). The results allow for proving that both systems provide consistent internal relative humidity measurements aligned with the exposure conditions and highlight the capability of fully embedded wireless sensors as a practical and reliable alternative to the conventional borehole method. Additionally, the continuous monitoring of the wireless cast-in sensor exhibits reliability during unintended temperature fluctuations, emphasizing the effectiveness of permanently installed sensors in promptly detecting unintended curing variations in real time. The continuous real-time information provided combined with the practicality of these sensors might assist construction managers to improve the quality control of the concrete curing process and shrinkage behavior, and ensure the integrity of concrete surface finishing.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Wireless Module for Nondestructive Testing/Structural Health Monitoring Applications Based on Solitary Waves

Ritesh Misra,Hoda Jalali,Samuel J. Dickerson,Piervincenzo Rizzo

DOI: https://doi.org/10.3390/s20113016

IF: 3.9

2020-05-26

Sensors

Abstract:In recent years, there has been an increasing interest in the use of highly nonlinear solitary waves (HNSWs) for nondestructive evaluation and structural health monitoring applications. HNSWs are mechanical waves that can form and travel in highly nonlinear systems, such as granular particles in Hertzian contact. The easiest setup consists of a built-in transducer in drypoint contact with the structure or material to be inspected/monitored. The transducer is made of a monoperiodic array of spherical particles that enables the excitation and detection of the solitary waves. The transducer is wired to a data acquisition system that controls the functionality of the transducer and stores the time series for post-processing. In this paper, the design and testing of a wireless unit that enables the remote control of a transducer without the need to connect it to sophisticated test equipment are presented. Comparative tests and analyses between the measurements obtained with the newly designed wireless unit and the conventional wired configuration are provided. The results are corroborated by an analytical model that predicts the dynamic interaction between solitary waves and materials with different modulus. The advantages and limitations of the proposed wireless platform are given along with some suggestions for future developments.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Monitoring and estimate of concrete compressive strength in full curing period using smart piezoelectric modules

Wei Sun,Pizhong Qiao,Shi Yan,Baoxin Qi,Jun Du,Linhan Lu

DOI: https://doi.org/10.1680/jmacr.22.00028

IF: 2.46

2022-08-31

Magazine of Concrete Research

Abstract:Concrete compressive strength is one of the most important material performance indices which can reflect the quality of concrete materials. In this paper, an innovative test method is proposed for monitoring development of concrete compressive strength in full curing period using smart piezoelectric modules (SPMs). The proposed method overcomes the shortcomings of traditional concrete detection methods, and it can realize nondestructive, real time, continuous and in-situ monitoring of concrete strength during the whole curing period of concrete structures. A series of experiments are conducted to demonstrate the validity and effectiveness of the approach using SPMs. It is clear that the energy values of monitoring signals from SPMs can be applied as the characteristic identification parameter for concrete compressive strength. The signal waveform and frequency suitable for monitoring of concrete compressive strength are determined, and a standard test procedure using SPMs in monitoring of concrete compressive strength is defined. Finally, the equations for correlating the signal energy ratio and compressive strength ratio of different grade concrete (i.e., C30, C40 and C50) based on the monitoring data from SPMs are established. The compressive strength of concrete under the given curing age can be effectively predicted by the present monitoring test method using SPMs and the established correlation equations, which are capable of assessing the concrete condition and strength in the whole curing period.

construction & building technology,materials science, multidisciplinary
Ultrasonic monitoring of the early-age hydration of mineral admixtures incorporated concrete using cement-based piezoelectric composite sensors

Youyuan Lu,Hongyan Ma,Zongjin Li

DOI: https://doi.org/10.1177/1045389x14525488

IF: 2.7

2014-02-25

Journal of Intelligent Material Systems and Structures

Abstract:The early-age hydration processes of concretes with mineral admixtures have been monitored and evaluated by a newly developed ultrasonic method based on embedded cement-based piezoelectric composite sensors. With the embedded ultrasonic (P-wave) measurement system, the waveform, wave velocity, attenuation coefficient index, and frequency-domain spectrum of detected ultrasonic waves during hydration can be recorded. The mineral admixtures examined include fly ash, slag, and silica fume, which replace part of the cement in concrete mixtures. It is found that the ultrasonic transmission parameters can be related to the microstructure changes of the concrete. Both the acceleration effects of silica fume and the retardation effects of fly ash and slag on the early hydration of concrete can be determined and explained through the analysis and comparison of the characteristics of the velocity curves. The attenuation coefficient index curve provides additional observation for the study of hydration kinetics. Moreover, the function of fresh concrete in filtering the high-frequency component of the wave varies with time, and concrete can be considered as low-pass frequency spectral filter. Frequency spectra analysis at different ages of fresh concrete provides useful information to reveal the early-age hydration process.

materials science, multidisciplinary
Study of Concrete's Behavior under 4-Point Bending Load Using Coda Wave Interferometry (CWI) Analysis

Y. Zhang,O. Abraham,X. Chapeleau,L-M Cottineau,V. Tournat,A. Le Duff,B. Lascoup,O. Durand

DOI: https://doi.org/10.1063/1.4789075

2013-01-01

AIP Conference Proceedings

Abstract:Coda Wave Interferometry (CWI) is an ultrasonic NDT method suitable for complex material such as concrete that can precisely measure small propagation velocity variation (10(-2)%). By measuring variation of propagation velocity in concrete caused by acoustoelasticity phenomena, CWI analysis can be used to monitor concrete's internal stress level. For the first time, CWI is used to measure propagation velocity variations due to a stress field in a concrete beam under four-points bending test, which contains simultaneously compressive and tensile stress. Embedded optical-fiber sensors, strain gauges are used in the experiment, in order to confirm and validate the CWI analysis result. Thermocouples are also embedded into concrete beams for monitoring internal temperature fluctuations.
Nondestructive Curing Monitoring of Early-Age Concrete Using Rayleigh Wave Velocity

Sung Woo Shin,Chung Bang Yun

DOI: https://doi.org/10.4028/www.scientific.net/kem.321-323.318

2006-01-01

Key Engineering Materials

Abstract:A modified one-sided Rayleigh wave (R-wave) velocity measurement technique is applied to monitor the strength gain of early-age concrete. A series of experiments were performed on early-age concrete specimens with various curing conditions. The results show that the R-wave velocity and strength gain has a strong relationship and that the R-wave velocity can be effectively used to monitor the strength development of the early-age concrete.
Distributed fiber optic sensing for internal strain monitoring in full life cycle of concrete slabs with BOFDA technology

Shun Wang,Zhihong Yang,Lipi Mohanty,Chaoyang Zhao,Chengjia Han,Bing Li,Yaowen Yang

DOI: https://doi.org/10.1016/j.engstruct.2024.117798

IF: 5.582

2024-04-01

Engineering Structures

Abstract:Effective health monitoring of concrete structures is vital in structural and geotechnical engineering, especially for internal monitoring in harsh environments. This article presents and validates a solution for distributed fiber optic sensing (DFOS) using Brillouin optical frequency-domain analysis (BOFDA) technology for monitoring the internal strain throughout the life cycle of common concrete slabs. The principle and sensing mechanism of BOFDA are briefly introduced and analyzed. A well-designed and deployed fiber under test (FUT) layout is utilized to accurately capture the internal strain distribution of a concrete slab. Besides, fiber Bragg grating (FBG) sensors and a thermocouple probe are incorporated for point strain reference and global temperature compensation. This paper presents a comprehensive monitoring method of concrete slabs throughout their entire life cycle. The monitoring process covers the preparation, pouring, curing, corrosion, and loading stages. Our experimental results demonstrate the feasibility of holistically monitoring strain distribution in concrete slabs over their lifetime. Additionally, post-processing of the data enables tracking of strain evolution at specific sensor nodes of interest. Furthermore, our study includes an extreme loading scenario, allowing examination of the strain variation process at rebars and key nodes. The strain distribution patterns observed in the experiment align with the finite element simulation results. These findings provide valuable guidance for crack prediction and structural health monitoring (SHM) of concrete slabs. The proposed scheme offers a unique and highly precise solution for full life-cycle SHM capable of functioning effectively in harsh environments such as energization and saltwater corrosion, thereby expanding its potential applications.

engineering, civil
Improved Rayleigh Wave Velocity Measurement for Nondestructive Early-Age Concrete Monitoring

Sung Woo Shin,Chung Bang Yun,John S. Popovics,Jae Hong Kim

DOI: https://doi.org/10.1080/09349840601128762

2007-01-01

Research in Nondestructive Evaluation

Abstract:A modified one-sided technique is proposed for Rayleigh wave ( R-wave) velocity measurement in concrete. Wave scattering from material heterogeneity and near-field effects may disrupt sensed R-wave signals in concrete, which is manifested as signal dispersion. Conventional one-sided measurement techniques for concrete do not consider dispersion of R-waves. In this study, the maximum energy arrival concept is adopted to determine the wave velocity by employing continuous wavelet transform. Experimental and numerical studies are performed to show the effectiveness of the proposed method. The method is applied to monitor the strength development of early-age concrete exposed to various curing conditions. Results reveal that the proposed method can be effectively used to measure the R-wave velocity in concrete structures and further to monitor the development of compressive strength in early-age concrete, regardless of the concrete moist curing condition.

HIV infection in greek intravenous drug users

Monitoring the curing process of in-situ concrete with piezoelectric-based techniques – A practical application

Monitoring the Setting Process of Cementitious Materials Using Guided Waves in Thin Rods

New Directions in Concrete Health Monitoring Technology

Non-destructive concrete strength evaluation using smart piezoelectric transducer—a comparative study

Electrical Based Sensors and Remote Monitoring System for Assessing the Corrosion Related Activity in Concrete at Hangzhou Bay Bridge

A novel ultrasonic-velocity-based concrete carbonation monitoring method based on step-wise stretching technique

Piezoelectric-based non-destructive monitoring of hydration of reinforced concrete as an indicator of bond development at the steel–concrete interface

Establishment of a Mass Concrete Strength-Monitoring Method Using Barium Titanate–Bismuth Ferrite/Polyvinylidene Fluoride Nanocomposite Piezoelectric Sensors with Temperature Stability

Piezoelectric sensor based nondestructive active monitoring of strength gain in concrete

Application of Distributed Optical Fiber Sensing Technology to the Detection and Monitoring of Internal Swelling Pathologies in Massive Concrete Blocks

Monitoring of Strength Gain in Concrete Using Smart Pzt Transducers

Wireless strain and temperature monitoring in reinforced concrete using Surface Acoustic Wave (SAW) sensors

Embedded Wireless Sensor for In Situ Concrete Internal Relative Humidity Monitoring

Wireless Module for Nondestructive Testing/Structural Health Monitoring Applications Based on Solitary Waves

Monitoring and estimate of concrete compressive strength in full curing period using smart piezoelectric modules

Ultrasonic monitoring of the early-age hydration of mineral admixtures incorporated concrete using cement-based piezoelectric composite sensors

Study of Concrete's Behavior under 4-Point Bending Load Using Coda Wave Interferometry (CWI) Analysis

Nondestructive Curing Monitoring of Early-Age Concrete Using Rayleigh Wave Velocity

Distributed fiber optic sensing for internal strain monitoring in full life cycle of concrete slabs with BOFDA technology

Improved Rayleigh Wave Velocity Measurement for Nondestructive Early-Age Concrete Monitoring