Abstract:To further clarify the effect mechanism of MoS 2 element diffusion on tribological properties of cemented carbide materials, an investigation was carried in this study. The diffusion process between cemented carbide inserts and MoS 2 powder under high temperature condition was carried out in a muffle furnace device. The surface morphology and chemical element content of test samples were observed and measured with scanning electron microscope, energy spectrum, and X-ray diffraction instruments. The kinetics of the diffusion process was quantitatively discussed by thermodynamic experiments. Tribological experiments were carried out using friction and wear machine with which the friction coefficient and wear scar were obtained. The experimental results show that high temperature has a significant effect on physical and mechanical properties of cemented carbide materials. Moreover, MoS 2 elements diffusion on sample surface is existed and induced by thermal action, which results in a further changing of material properties of cemented carbide. The WC grain growth is inhibited when molybdenum element is only infiltration on sample surface at 500 °C, which improves the surface morphology and hardness of test sample. However, the oxidation rate, friction coefficient, and wear rate of test sample are the highest when heating temperature larger than 500 °C. The main reason is that, as the temperature increasing, the diffusion of sulfur elements is occurred and intensified the loss of cobalt element on sample surface. So, the bonding ability of it is decreased due to the loss of bonding phase Co. Thus, the surface hardness and wear resistance of test sample is deteriorated. This study provides a theoretical foundation for the application of molybdenum disulfide in tool cutting lubrication condition.

Effect of Nickel Element Diffusion on the Tribological Properties of Cemented Carbide Materials under High Temperature Condition

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effect of MoS 2 element diffusion under high temperature condition on the tribological properties of cemented carbide materials

Effect of Workpiece Atom Diffusion Into CBN Tool on Its Mechanical Properties in Cutting Ni–Fe–Cr Alloy Based on Molecular Dynamics Simulation

Effects of Temperature and Normal Load on Tribological Behavior of Nickel-Based High Temperature Self-Lubricating Wear-Resistant Composite Coating

Influence of Residual Stress on the High-Temperature Tribological Performance of Nickel-Based Superalloy

Influence of Cu Content Variation on the Tribological Properties of Ni60CuMo with Sandwich-Structured Composite Coatings by Laser Cladding

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

Analysis of tool wear and cutting characteristics in milling of powder metallurgy nickel-based superalloy by various coatings

Effect of binder content and sintering time on the microstructure and mechanical properties of gradient cemented carbides with Ni binder

High temperature and room temperature tribological behaviors of in-situ carbides reinforced Ni-based composites by reactive sintering Ni and Ti2AlC precursor

Effect of element N on microstructure and tribological properties of CoCrFeNiV alloy at severe temperature

High-temperature tribological behavior of CoCrFeNiV high-entropy alloys: A parallel comparison with CoCrFeNiMn high-entropy alloys

Element diffusion behaviors at high temperature and their effects on microstructure and tribological properties of Cr2O3 films

The effect of nickel on the carbide precipitation behavior in Cr–Mo–V hot-working die steel

Effects of Nickel on the Oxide/Metal Interface Morphology and Oxidation Rate During High-Temperature Oxidation of Fe–Cu–Ni Alloys

Effect of aluminum addition on microstructure, mechanical properties and high temperature tribological properties of nickel-rich NiTi alloy

Wear and friction analysis of cubic boron nitride tools with different binders in high-speed turning of nickel-based superalloys

Study on the adhering failure mechanism of cemented carbide inserts and element diffusion model during the heavy-duty cutting of water chamber head

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Molecular Dynamics and Experimental Investigation on the Interfacial Binding Mechanism in the Fe/Cu1−x-Nix Bimetallic Interface