Abstract:By reaction of PbC2O4 and TiO2 in the eutectic NaCl-KCl salts, both sphere- and rod-like PbTiO3 (PTO) powders were synthesized via molten salt synthesis (MSS) and template MSS methods, respectively. X-ray diffraction patterns reveal that all the PTO powders crystallize in a tetragonal phase structure. Increasing the molar ratio of PbC2O4:TiO2:NaCl:KCl from 1:1:10:10 to 1:1:60:60 in the MSS process has little effect on the sphere-like morphology of the PTO powders synthesized at 950 °C for 5 h. Large-scale polycrystalline rod-like PTO powders with diameters of 480 nm–1.50 μm and lengths up to 10 μm were synthesized at 800 °C for 5 h by template MSS method, where the rod-like anatase TiO2 precursors were used as templates and the molar ratio of PbC2O4:TiO2:NaCl:KCl was equal to 1:1:60:60. X-ray energy dispersive spectroscopy spectra reveal that all the PTO powders are composed of Pb, Ti, and O elements, and the measured Pb:Ti atomic ratios are close to 1:1. In the template MSS process, the molten salt content plays an important role in forming the rod-like PTO powders. Under low molten salt content, the rod-like PTO powders cannot be synthesized even if the rod-like TiO2 templates are used. In addition, prolonging the reaction time suppressed the formation of rod-like PTO powders but promoted the formation of sphere-like PTO nanoparticles. The dielectric properties the sphere- and rod-like PTO powders were comparatively investigated. At room temperature, the dielectric constant and dielectric loss of the spherical PTO powders synthesized by MSS method with the molar ratio of PbC2O4:TiO2:NaCl:KCl equal to 1:1:30:30 were ~ 340 and 0.06 (measured at 106 Hz), respectively. The corresponding values for the rod-like PTO powders synthesized by template MSS method with the molar ratio of PbC2O4:TiO2:NaCl:KCl equal to 1:1:60:60 were 140 and 0.08, respectively. The present results demonstrate the sphere-like PTO powders have better dielectric properties, which have promising applications in the fields of multilayer capacitors and resonators.

Synthesis of CaCu3Ti4O12 Micron-cubes and rods via high proportion molten salt method

Microwave-Assisted Synthesis of High Dielectric Constant CaCu 3 Ti 4 O 12 from Sol–Gel Precursor

In-situ Synthesis of Nanocrystalline TiC Powders, Nanorods, and Nanosheets in Molten Salt by Disproportionation Reaction of Ti(II) Species

Synthesis, characterization, and morphological control of CaCu3Ti4O12 through modify sol–gel method

Molten-salt Synthesis of BaTiO3 Powders and Their Atomic-Scale Structural Characterization

Preparation and characterization of CaCu3Ti4O12 powders by non-hydrolytic sol–gel method

Synthesis of Calcium Copper Titanate Ceramics Via the Molten Salts Method

Structural Characterizations and Dielectric Properties of Sphere- and Rod-Like PbTiO3 Powders Synthesized Via Molten Salt Synthesis.

Preparation and characterization of CaCu 3 Ti 4 O 12 powders by non-hydrolytic sol–gel method

Tabular SrTiO3 Synthesized by Two-Step Molten Salt Method

Synthesis, phase structure and dielectric properties of CoTiTa2O8 by molten salt method for LTCC application

Synthesis of Large Diameter Plat-Like Ca3co4o9 Particle by Molten Salt Method

Sintering and Microstructure of BaTiO3 Nano Particles Synthesized by Molten Salt Method

Giant Dielectric Permittivity and Non-Linear Electrical Behavior in CaCu3Ti4O12 Varistors from the Molten-Salt Synthesized Powder

Structural and dielectric properties of CaCu3Ti4O12 synthesized by sol–gel method

Synthesis, phase structure and dielectric properties of MgTiTa2O8 by molten salt method

Tabular Sr3Ti2O7 Intermediates Synthesized by Molten Salt Method

Oleic Acid Assisted Synthesis of CaCu3Ti4O12 Powders and Ceramics by Sol–gel Process

Grain Size Effect on the Dielectric and Non-Ohmic Properties of CaCu3Ti4O12 Ceramics Prepared by the Sol-Gel Process

Rapid Fabrication and Improved Electrical Properties of CaCu3Ti4O12 Ceramics by Sol–gel and Spark Plasma Sintering Techniques

Enhanced Electrical Properties of CaCu3Ti4O12 Ceramics by Spark Plasma Sintering: Role of Zn and Al Co-Doping