Abstract:Corrosion of metal plays a detrimental role in service lifetime of parts or systems. Therefore, coating a protective film which is fully dense and defects free on the base metal is an effective approach to protect the base metal from corrosion. In this study, a dense NiCr-20Mo coating with excellent lamellar interface bonding was deposited by plasma spraying of the novel shell–core–structured Mo-clad-NiCr powders, and then post-spray shot peening treatment by cold spraying of steel shots was applied to the plasma-sprayed NiCr-20Mo coating to obtain a fully dense coating through eliminating possibly existed pores and un-bonded interfaces within the NiCr-20Mo coating. Corrosion behaviors of the NiCr-20Mo coatings before and after shot peening were tested to investigate the effect of the post-spray shot peening on the corrosion behavior of the NiCr-20Mo coating. Results showed that a much dense and uniform plasma-sprayed NiCr-20Mo coating with perfect lamellar bonding at most of interfaces was deposited. However, the electrochemical tests revealed the existence of through-thickness pores in the as-plasma-sprayed NiCr-20Mo coating. Through the post-spray shot peening treatment, a completely dense top layer in the coating was formed, and with the increase in the shot peening intensity from one pass to three passes, the dense top layer became thicker from 100 μm to reach 300 μm of the whole coating thickness. Thus, a fully dense bulk-like coating was obtained. Corrosion test results showed that the dense coating layer resulting from densification of shot peening can act as an effective barrier coating to prevent the penetration of the corrosive medium and consequently protect the substrate from corrosion effectively. Therefore, a fully dense bulk-like NiCr-20Mo coating with excellent corrosion resistance can be achieved through the plasma spraying of Mo-clad-NiCr powders followed by appropriate post-spray shot peening treatment.

Development of Galvanic Pulse Deposited and Ultrasonic Shot Peening-Based Ni-Cr Hybrid Coatings

Effect of ultrasonic shot peening on electrodeposited Ni and Cu coatings on Cu substrate

Cooperative enhancement of strength and corrosion resistance through architecture of nanotwins and low angle grain boundary in Ni20Cr alloy

Enhanced corrosion resistance of the surface modified Ti-13Nb-13Zr alloy by ultrasonic shot peening

Effect of ultrasonic surface shot peening on the microstructure and properties of Cu-8Cr alloy

Enhanced Tribological Properties of CrN Coatings on Densified Surfaces of Fe-Based Porous Materials Obtained Through Powder Metallurgy and Ultrasonic Shot Peening Treatment

Effects of Ultrasonic Shot Peening and Multi-arc Ion Plating on Microstructure and Properties of TiAlN-Coated Cemented Carbide Materials

Experimental Investigation on Ultrasonic Shot Peening of WC-Co Alloy

Ultrasonic shot peening of 316L stainless steel – Experimental and analytical approach

Surface Nanocrystallization of Pure Cu Induced by Ultrasonic Shot Peening

Effects of ultrasonic shot peening process on the microstructure and mechanical properties of nickel-based superalloys formed by selective laser melting

Effect of Ultrasonic Shot Peening on Surface Mechanical and Wear Behavior of Aluminum 7075-T651 Alloy

Mechanical Properties and Tribological Behaviour of Electroless Ni–P–Cu Coatings on Corrosion-Resistant Alloys under Ultrahigh Contact Stress with Sprayed Nanoparticles

Influence of Ultrasonic Shot Peening on Microstructure, Mechanical, and Electrochemical Behavior of 316 Stainless Steel

Effect of ultrasonic shot peening duration on the microstructure and mechanical properties of CrMnFeCoNi high-entropy alloy

Effect of Shot Peening on Surface Damage Evolution Behavior of Cu-19Ni Alloy

Errosion-Corrosion Critical Performance of Surface Nanocrystalline 20 Carbon Steel in Condensate Water

Surface characteristics and microstructure evolution of a nickel-base single crystal superalloy treated by ultrasonic shot peening

Effect of Ultrasonic Shot Peening and Laser Shock Peening on the Microstructure and Microhardness of IN738LC Alloys

Effect of Post-spray Shot Peening Treatment on the Corrosion Behavior of NiCr-Mo Coating by Plasma Spraying of the Shell–Core–Structured Powders